Hardinge Lathes


Page 1 of 26 123411 ... LastLast
Threads 1 to 20 of 519

Forum: Hardinge Lathes

Discuss Hardinge Lathes here.

  1. CONOUEST 42

    Started by geiges‎, 12-16-2014 05:05 AM
    198, 1989, 989, conouest, control, don, fanuc, fanuc ot, fanuc ot control, find, ge fanuc, help me, ion, jest, know, lathe, looked, machine, manuals, pdf, poi, point, wha, works
    • Replies: 2
    • Views: 828
    Yesterday, 01:59 AM Go to last post
  2. Hardinge HC-AT threading attachment

    Started by mtlhe‎, 12-01-2014 09:54 PM
    • Replies: 1
    • Views: 819
    07-17-2018, 02:24 AM Go to last post
  3. Sodick

    Started by outctrl‎, 08-01-2013 01:51 PM
    • Replies: 2
    • Views: 681
    06-27-2018, 09:19 PM Go to last post
  4. Cobra 42 21T backup

    Started by cooperjm‎, 06-07-2018 07:18 PM
    backup, ladder, card, controller, 21t
    • Replies: 8
    • Views: 381
    06-11-2018, 04:33 AM Go to last post
  5. Cobra 42 Fusion 360 post

    Started by cooperjm‎, 06-07-2018 07:15 PM
    post, fusion, make, edited, tapatalk
    • Replies: 0
    • Views: 72
    06-07-2018, 07:15 PM Go to last post
  6. Need Help!- Hardinge CHNC III Turret Gearbox

    Started by itanium7000‎, 05-25-2018 10:25 PM
    cnc, hardinge, shaft, turret, worm
    • Replies: 0
    • Views: 241
    05-25-2018, 10:25 PM Go to last post
  7. HARDINGE CHNC 1 WIRING SCHEMATIC

    Started by moonman5‎, 02-07-2017 06:12 AM
    • Replies: 10
    • Views: 1,504
    05-07-2018, 02:00 PM Go to last post
  8. Problem- Hardinge GN-6 Superslant - Spindle fault

    Started by NEC‎, 11-19-2015 02:48 PM
    • Replies: 7
    • Views: 764
    04-23-2018, 11:15 AM Go to last post
  9. Hey, finally a section for one of my favorite lathes.

    Started by g-codeguy‎, 05-08-2008 09:27 AM
    3 Pages
    1 2 3
    maybe, not, took
    • Replies: 25
    • Views: 4,583
    04-20-2018, 09:18 AM Go to last post
    • Replies: 0
    • Views: 107
    04-19-2018, 10:49 AM Go to last post
    • Replies: 8
    • Views: 286
    04-18-2018, 05:24 PM Go to last post
  10. Can I join the club? I have a T42 too.

    Started by torinwalker‎, 04-17-2018 10:32 PM
    offset, spindle, sub-spindle, t42, working
    • Replies: 0
    • Views: 124
    04-17-2018, 10:32 PM Go to last post
  11. Need Help!- Conquest T42: Opening main collet more than few seconds trips hydraulic motor breaker

    Started by torinwalker‎, 03-14-2018 08:21 PM
    3 Pages
    1 2 3
    • Replies: 33
    • Views: 937
    04-14-2018, 09:21 PM Go to last post
  12. New Machine Build- Stepper Motor verses Ball Screw Relationships

    Started by DDjrouter‎, 04-07-2018 10:59 PM
    ball, diameter, engineering, screw, stepper
    • Replies: 4
    • Views: 225
    04-08-2018, 01:37 PM Go to last post
  13. Build Thread- spindle drive for CHNC-I

    Started by jmelson‎, 04-07-2018 12:20 PM
    drive, fanuc, motor, original, spindle
    • Replies: 6
    • Views: 232
    04-07-2018, 11:46 PM Go to last post
  14. Build Thread- Fanuc OT to DC_CNC conversion.

    Started by Jim Dawson‎, 02-09-2018 12:36 AM
    • Replies: 8
    • Views: 650
    04-07-2018, 01:10 AM Go to last post
  15. Need Help!- Hardinge conquest SP parameters lost!

    Started by justinzwier‎, 04-02-2018 02:30 PM
    conquest, hardinge conquest, made, parameters, parameters needed
    • Replies: 0
    • Views: 125
    04-02-2018, 02:30 PM Go to last post
  16. Need Help!- Post for BobCad software

    Started by Machineit‎, 03-29-2018 06:36 PM
    bobcad, lathe, license, post, software
    • Replies: 3
    • Views: 238
    03-30-2018, 09:19 AM Go to last post
  17. Need Help!- Hardinge HNC with Fanuc 21-T controller will not power display

    Started by timjz‎, 03-03-2018 01:55 PM
    • Replies: 4
    • Views: 359
    03-25-2018, 08:31 AM Go to last post
  18. Need Help!- Can you Identify these Shop-Made Hardinge Tool Holders?

    Started by JohnnyTurn‎, 03-17-2018 02:24 PM
    • Replies: 0
    • Views: 127
    03-17-2018, 02:24 PM Go to last post

Page 1 of 26 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 13 users browsing this forum. (0 members & 13 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands