Make sure BOTH of the emergency stops are off, then clear the alarms. You can do nothing until that alarm is cleared. I had a bad E-stop switch on mine once.
Hi All,
Subject to my previous post on my Hardinge CNHC1 Siemens 810T control, So now I have managed to get the machine to power up (the fault was a short in the turret encoder) It took
me an age to find! I have removed the faulty unit, looks like its sealed in some sort of resin?
I now have a 6000 Emergency Stop, my question is will the machine give me this E-stop even though I have removed the faulty unit (I thought I might still be able to move the axis and maybe
start the spindle? as I do not get any alarms related to the turret?
Thanks for any help.
Allen
Similar Threads:
- Need Help!- Hardinge chnc ii
- Need Help!- Hardinge CHNC 1 with Hardinge Bar Feeder Trouble
- HELP ME! Mazak alarm 207 EXT EMERGECY STOP
- Need Help!- Hardinge CHNC I
- Hardinge CHNC
Make sure BOTH of the emergency stops are off, then clear the alarms. You can do nothing until that alarm is cleared. I had a bad E-stop switch on mine once.
Two Haas VF-2's, Haas HA5C, Haas HRT-9, Hardinge CHNC 1, Bother HS-300 Wire EDM, BobCAD V23, BobCAD V28
Hi,
Thanks for your reply greatly appreciated, Yes I have done that, I have also checked both e-stops with a digital meter and both are good, The machine is not on the hard stops (I always move the axis
well clear of the limit switches before I shut the machine down,
Is it possible with the turret encoder removed that this would cause the e-stop? (6000)
Thanks Allen.
Nope, looks like just the e-stop switch.
See attached
Two Haas VF-2's, Haas HA5C, Haas HRT-9, Hardinge CHNC 1, Bother HS-300 Wire EDM, BobCAD V23, BobCAD V28
I have a spare E stop switch if needed ! ed.murch@mamcomolding.com
Ed
That's good, hope you find the problem. Hard to help you from long distance!
Two Haas VF-2's, Haas HA5C, Haas HRT-9, Hardinge CHNC 1, Bother HS-300 Wire EDM, BobCAD V23, BobCAD V28
Hi,
Thanks for the attachment, a great help! So you don't think that with the turret encoder completely removed it will give me an E-stop? that was my thoughts? do you think it could be a faulty limit switch?
I have been trying all day to clear the alarm but no luck
Thanks again for your help
Allen.
Hi Ed,
what about a Turret encoder?
Thanks,
Allen
Allen,
What # is on yours ? C2-137B Can't read the number on the other one
ed
Hi Ed,
Yes! that's exactly the same number, C2-137B Have you got one?
Allen.
Allen,
Yes i do !!!!! Make me a fair offer . Is there anything else you need ? Give me an address to send ! Can you pay by paypal ? If so i can send you an invoice .
Ed
Hi Ed,
Yes I can pay via PayPal, I don't no where to start with an offer, got no idea what they cost new (not that you can get them now) I am in the Uk so obviously there will be postage costs
Can you give me a price or somewhere to start?
Allen
Allen,
company owner said $150 with shipping and i well give you a e stop ! How does that sound ?
Ed
Hi Ed,
Yes that sounds ok to me, can you just confirm that the part is in good working order, and also I will need your e-mail address to send money via PayPal,
Thank you,
Allen
Allen,
I myself removed it ! It was working fine when removed a month ago . ed.murch@mamcomolding.com is mine . alyssa.albert@mamcomolding.com send for payment and address to send parts
thanks
Ed
Hi Ed,
So you have given me two E-mails what one should I send money to? bit confused with your reply,
Allen.