Problem Conquest 42 / Fanuc 0-TC / Parameters needed


Results 1 to 17 of 17

Thread: Conquest 42 / Fanuc 0-TC / Parameters needed

  1. #1
    Registered
    Join Date
    Jul 2012
    Location
    Canada
    Posts
    7
    Downloads
    0
    Uploads
    0

    Default Conquest 42 / Fanuc 0-TC / Parameters needed

    Hi there,

    I have this Conquest 42 with Fanuc 0-TC, serial number is CS-1337-C. It lost parameters when I changed the keypad that was falling apart, and the new one was too tight and obviously kept a couple buttons pushed in when I turned it on...

    I contacted Hardinge USA and the service guy sent me 3 files which are '900 stsndard cPAR~1.txt', 'CSGENERAL.TXT.dat' and 'CSMACRO.txt'. He told me they were generic files for that Conquest series and not specific to my machine. Needless to say, it didn't helped me much. Those '900 stsndard cPAR~1.txt' parameters bring alarm 409 and 1008 with the load meter maxing out and AL-34 in the back board. I've narrowed the P917 being the cause of it, and if I leave it as in 'CSGENERAL.TXT.dat', I don't get those alarms. Instead, I get the 1004 alarm even though the brake does work. I can do the zero return, but it doesn't get out of the ZRN state. It doesn't go to 'auto' and ready.

    Would someone with comparable machine be able to send me his parameters?

    -It has 10’’x14’’ travel, 10 stations turret with 5 live tools, tailstock, tool probe.
    -It doesn’t have sub-spindle, part catcher, barfeeder, air blast, hi pressure coolant.
    -Not sure if C is full or indexer, we’ve only used it as indexer. The first guy to set it up for us said the backup batteries were dead and parameters gone. I don’t know what he did to make it work. We’ve only been able to use the C as indexer since then though.

    Any help would be appreciated. Thank you.

    Similar Threads:


  2. #2
    Registered
    Join Date
    Jul 2007
    Location
    USA
    Posts
    34
    Downloads
    0
    Uploads
    0

    Default Re: Conquest 42 / Fanuc 0-TC / Parameters needed

    Did you get the 300 series diagnostic bits to tell the brain what kind of machine you have - 10/12 station turret, live tooling/not, tailstock/subspindle, like that?
    Regards,
    Newc



  3. #3
    Community Moderator Al_The_Man's Avatar
    Join Date
    Dec 2003
    Location
    Canada
    Posts
    24216
    Downloads
    0
    Uploads
    0

    Default Re: Conquest 42 / Fanuc 0-TC / Parameters needed

    PM sent.
    Al.

    CNC, Mechatronics Integration and Custom Machine Design

    “Logic will get you from A to B. Imagination will take you everywhere.”
    Albert E.


  4. #4
    Registered
    Join Date
    Jul 2012
    Location
    Canada
    Posts
    7
    Downloads
    0
    Uploads
    0

    Default Re: Conquest 42 / Fanuc 0-TC / Parameters needed

    Quote Originally Posted by newc View Post
    Did you get the 300 series diagnostic bits to tell the brain what kind of machine you have - 10/12 station turret, live tooling/not, tailstock/subspindle, like that?
    Regards,
    Newc
    No, that is not something I got. What Hardinge sent me was the P900's for 0TC, and the P0-P900 + P8000 for generic CS.

    If someone has diagnostic parameters, I'd like to take a look a those. And if for 10 station turret / Live tooling / tailstock / tool setter touch probe, that'd be even better. But I'll take a look at anything.

    Thanx



  5. #5
    Registered
    Join Date
    Jul 2012
    Location
    Canada
    Posts
    7
    Downloads
    0
    Uploads
    0

    Default Re: Conquest 42 / Fanuc 0-TC / Parameters needed

    Or would someone have the Fanuc 0-T parameters manual? That could help me I guess.



  6. #6
    Community Moderator Al_The_Man's Avatar
    Join Date
    Dec 2003
    Location
    Canada
    Posts
    24216
    Downloads
    0
    Uploads
    0

    Default Re: Conquest 42 / Fanuc 0-TC / Parameters needed

    Emailed over.
    Al.

    CNC, Mechatronics Integration and Custom Machine Design

    “Logic will get you from A to B. Imagination will take you everywhere.”
    Albert E.


  7. #7
    Registered
    Join Date
    Jul 2012
    Location
    Canada
    Posts
    7
    Downloads
    0
    Uploads
    0

    Default Re: Conquest 42 / Fanuc 0-TC / Parameters needed

    You the man. That's 0-TD, but I guess it's worth looking into an try a couple things, see how far off (or not) those are from 0-TC. Thank you.
    Quote Originally Posted by Al_The_Man View Post
    Emailed over.
    Al.
    If anyone has 0-TC programming manual, I'm still interested.



  8. #8
    Member sting007's Avatar
    Join Date
    Feb 2015
    Location
    44635
    Posts
    96
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by MorueM View Post
    You the man. That's 0-TD, but I guess it's worth looking into an try a couple things, see how far off (or not) those are from 0-TC. Thank you.


    If anyone has 0-TC programming manual, I'm still interested.
    Hi,
    Did you solved your problem, I am facing same problem
    Would you please send a copy of the parameters?
    Sting



  9. #9
    Member
    Join Date
    May 2016
    Location
    Italy
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default Re: Conquest 42 / Fanuc 0-TC / Parameters needed

    Hello to all!!! I'm new in this forum and I'm come from Italy where I actually work for a small company that is interested in turning.

    Recently, we bought from a company near here a Hardinge Conquest 42 but in these days we had a big problem due to a fault and, for this reason, we have lost all the parameter of this machine.
    Now we can't work with this machine and in these days I tried to ask to Hardinge's company (in Italy, in Germany and in United States) and Fanuc's company these parameters but everyone sent me just general parameters but neither of them was correct for this machine; I tried also to ask to the company that had the machine previously but no one had these parameters.They also said me that I have to find something similar to my machine and I have to try to upload these new parameters.

    For this reason, I think that my only remaining hope is that someone in this forum has a similar machine to mine.

    Now, I try to write to everybody the features of my machine:

    Hardinge Conquest 42 with Fanuc 0-TC and serial CS - 1357 - C. I have live tooling, bar feed, part catcher, C axis (spindle orient), hydraulic tailstock.

    I kindly ask to all if someone has a machine similar to mine if can send me all the parameters and diagnostic and help me!!!

    My email address is: fabrizioturella.otra@gmail.com

    Thank you in advance



  10. #10
    Activation process daluchman's Avatar
    Join Date
    Aug 2018
    Posts
    2
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by Al_The_Man View Post
    Emailed over.
    Al.
    Are you able to email me over the same parameters for the Harding conquest T42?
    I lost them all and I need to get some jobs out like yesterday. I am dead in the water. If at all possible I am not quite sure how to load them back into machine so I would greatly appreciate any knowledge or information you can give me

    Thank you in advance



  11. #11
    Registered
    Join Date
    Feb 2012
    Location
    usa
    Posts
    6
    Downloads
    0
    Uploads
    0

    Default

    Hello AL , we have a Conquest 42 Fanuc 0T and the batteries died we lost all parameters..
    Would you be able to email me the list of nc parameters and the pc dgn 300-900..
    I have lots of machine parameters on file but nothing for this machine..Thank you
    in advance for your expertise..Tony email tnysoliz@yahoo.com
    I will reciprocate with any params you may need that i have...ie mori ikegai hyundia seiki..etc



  12. #12
    Member
    Join Date
    Sep 2014
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default Re: Conquest 42 / Fanuc 0-TC / Parameters needed

    FANUC 0-TC programming manual. I have got.



  13. #13
    Member
    Join Date
    Jan 2007
    Location
    Australia
    Posts
    11
    Downloads
    0
    Uploads
    0

    Default

    I am also in the same situation. Would anyone with the 0-TD parameters please send them to me?

    Dan



  14. #14
    Community Moderator Al_The_Man's Avatar
    Join Date
    Dec 2003
    Location
    Canada
    Posts
    24216
    Downloads
    0
    Uploads
    0

    Default Re: Conquest 42 / Fanuc 0-TC / Parameters needed

    The parameters are unique to the machine, compiled by the MTB at design time.
    Your only hope is either the OEM or anyone with the same machine.
    All I have is the Fanuc parameter manual, but all that gives is the parameter definitions, you also need the 900 option parameters.
    Al.

    CNC, Mechatronics Integration and Custom Machine Design

    “Logic will get you from A to B. Imagination will take you everywhere.”
    Albert E.


  15. #15
    Member
    Join Date
    Jan 2007
    Location
    Australia
    Posts
    11
    Downloads
    0
    Uploads
    0

    Default

    My issue is actually slightly different. I accidentally changed a parameter when trying to change the backlash compensation. As we all know when you change a parameter the first time it alarms out and goes to the alarm page. So I can't remember what page I was on. My issue is that it now has a different travel amount when jogging. I basically want to compare parameters from machine to machine. I can always look up the numbers that are different.

    Dan



  16. #16
    Member
    Join Date
    May 2014
    Posts
    174
    Downloads
    0
    Uploads
    0

    Default Re: Conquest 42 / Fanuc 0-TC / Parameters needed

    Hello tsoliz, would you happen to have a set of parameters for the HARDINGE VMC 700? It would be a life saver and greatly appreciated. Thank you in advance!

    peloflex@gmial.com

    Regards,

    peloflex


    Quote Originally Posted by tsoliz View Post
    Hello AL , we have a Conquest 42 Fanuc 0T and the batteries died we lost all parameters..
    Would you be able to email me the list of nc parameters and the pc dgn 300-900..
    I have lots of machine parameters on file but nothing for this machine..Thank you
    in advance for your expertise..Tony email tnysoliz@yahoo.com
    I will reciprocate with any params you may need that i have...ie mori ikegai hyundia seiki..etc




  17. #17
    Member Lunchbox1029's Avatar
    Join Date
    Feb 2022
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default Re: Conquest 42 / Fanuc 0-TC / Parameters needed

    I would be very interested in any and all manuals for a Conquest 42 with Fanuc 0T.



  18. #18
    ghiasi's Avatar
    Join Date
    Jan 2023
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default Re: Conquest 42 / Fanuc 0-TC / Parameters needed

    Plz send for me
    eng.ghiasi.2020@gmail.com



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Conquest 42 / Fanuc 0-TC / Parameters needed

Conquest 42 / Fanuc 0-TC / Parameters needed