Air Consumption on older Haas? - Page 5


Page 5 of 5 FirstFirst ... 2345
Results 81 to 85 of 85

Thread: Air Consumption on older Haas?

  1. #81
    Registered
    Join Date
    Sep 2013
    Location
    Cascadia, WA
    Posts
    54
    Downloads
    0
    Uploads
    0

    Default

    Thanks! I was worried I was gonna be chasing some switch all day but after hosing it down with a bottle of wd40 I'm back in business!



  2. #82
    Member Machineit's Avatar
    Join Date
    Mar 2010
    Location
    USA
    Posts
    1816
    Downloads
    0
    Uploads
    0

    Default Re: Air Consumption on older Haas?

    Personally I use a pry bar between the spindle and the tool. Don't like hitting anything and with my luck I'd hit the tool and break it!

    Mike

    P.S.: I also pry the tool slightly without hitting the release button, then you just hold the tool and take it out! Even though the tool is being held, it is not that difficult to overcome the washers with a nice pry-bar.

    Two Haas VF-2's, Haas HA5C, Haas HRT-9, Hardinge CHNC 1, Bother HS-300 Wire EDM, BobCAD V23, BobCAD V28


  3. #83
    Registered
    Join Date
    Sep 2013
    Location
    Cascadia, WA
    Posts
    54
    Downloads
    0
    Uploads
    0

    Default Re: Air Consumption on older Haas?

    Here's a couple oddball questions about using the leadscrew tables:
    Do I have to provide a value for every .5" increment, or can it automatically interpolate between them? That's a minimum of 80+40+48 measurements for my VF-3, not to mention I would want to do it few times to catch any fliers. Also there would have to be some (hopefully inconsequential) amount of backlash in the first move from the end of each axis, any ideas on how to account for that? Has anyone actually even used this? I have mapped out my entire machine on a 2" grid and I would like to give this a shot.
    Air Consumption on older Haas?-error_map-jpg
    X looks good aside from about .001" backlash, I'm mostly concerned about the .005" of undertravel in Y and the .002" in Z (not pictured).



  4. #84
    Member
    Join Date
    Aug 2015
    Posts
    4
    Downloads
    0
    Uploads
    0

    Default Re: Air Consumption on older Haas?

    I have a problem with my 1994 Haas VF0, please tell me this machine have always on air spindle lubrication even when emergency stop button is on ? When i turn off machine it stops blowing
    the spindle, but if i turn it on it starts cooling spindle all the time, this is normal ? My air compressor turn on all the time.through



  5. #85
    Member
    Join Date
    Aug 2015
    Posts
    4
    Downloads
    0
    Uploads
    0

    Default Re: Air Consumption on older Haas?

    I'm fix it ;-) i change transistor in main board,
    Air Consumption on older Haas?-7kb3dl5-jpg
    Back to work ;-D
    Air Consumption on older Haas?-ndj31nk-jpg

    Attached Thumbnails Attached Thumbnails Air Consumption on older Haas?-7kb3dl5-jpg   Air Consumption on older Haas?-ndj31nk-jpg  


Page 5 of 5 FirstFirst ... 2345

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Air Consumption on older Haas?

Air Consumption on older Haas?

Air Consumption on older Haas?