Granite Devices

Page 1 of 11 1234 ... LastLast
Threads 1 to 20 of 218

Forum: Granite Devices

Discuss about servo & stepper drives made by Granevices and get direct support!

  1. Newbie- Need some advice / Regarding; Argon drivers.

    Started by NeoTech‎, 12-29-2014 10:09 AM
    6i25, argon, card, drives, its, software, suggested
    • Replies: 1
    • Views: 880
    03-30-2018, 07:22 AM Go to last post
  2. emergency stop problem, unstable

    Started by machining fool‎, 12-02-2017 12:55 PM
    115vac, estop, mach3, power, problem
    • Replies: 3
    • Views: 1,337
    12-03-2017, 12:37 PM Go to last post
  3. Need serious help. Runaway axis on power up.

    Started by machining fool‎, 11-25-2017 06:58 AM
    2 Pages
    1 2
    • Replies: 21
    • Views: 575
    11-26-2017, 04:30 PM Go to last post
  4. Need Help!- Granite VSD-e drive flashing Red and Blue

    Started by machining fool‎, 11-23-2017 11:16 AM
    blue, drives, flashing, vsd-e, vsd-e drive problem
    • Replies: 1
    • Views: 166
    11-24-2017, 01:26 PM Go to last post
  5. Newbie- Need help connecting usb to VSD-e drive

    Started by machining fool‎, 11-24-2017 09:39 AM
    drive, forgot, gdtool, power, signal
    • Replies: 3
    • Views: 186
    11-24-2017, 01:23 PM Go to last post
  6. Will Argon drive work with Sanyo motor

    Started by medu2015‎, 07-26-2016 12:34 PM
    • Replies: 2
    • Views: 2,796
    07-29-2016, 12:10 AM Go to last post
  7. Is Granite Devices out of business?

    Started by Black Forest‎, 07-06-2016 07:03 AM
    asked, business, devices, granite, replies
    • Replies: 6
    • Views: 1,152
    07-22-2016, 09:35 AM Go to last post
  8. VSD-E drives

    Started by jnnewton‎, 06-10-2016 07:53 AM
    buy, drives, sell, vsd-e
    • Replies: 0
    • Views: 573
    06-10-2016, 07:53 AM Go to last post
    • Replies: 0
    • Views: 1,157
    02-23-2016, 02:09 PM Go to last post
    • Replies: 0
    • Views: 1,297
    01-26-2016, 06:42 AM Go to last post
    • Replies: 0
    • Views: 950
    11-28-2015, 04:44 PM Go to last post
  9. I am a newbie, Argon drive with Mach 3?

    Started by machining fool‎, 08-18-2015 01:06 PM
    argon, centipede, correct, drive, setup
    • Replies: 0
    • Views: 1,509
    08-18-2015, 01:06 PM Go to last post
  10. Newbie needs help with VSD-XE drive.

    Started by machining fool‎, 08-18-2015 10:40 AM
    adept, cnc, ksi, newbie, servo
    • Replies: 0
    • Views: 876
    08-18-2015, 10:40 AM Go to last post
  11. Question 2 encoders on ARGON

    Started by TomBuil‎, 08-06-2015 08:02 AM
    argon, encoder, linear, motor, position
    • Replies: 0
    • Views: 875
    08-06-2015, 08:02 AM Go to last post
  12. Electronic gearing

    Started by EFI-Unlimited‎, 07-23-2015 10:00 PM
    create, drive, electronic, gearing, heavy
    • Replies: 4
    • Views: 1,069
    07-25-2015, 07:14 PM Go to last post
  13. Will Argon drive work with a more powerful servo?

    Started by richienz‎, 05-04-2015 07:33 PM
    argon, drive, give, prob, servo
    • Replies: 3
    • Views: 1,807
    05-24-2015, 08:41 PM Go to last post
  14. New IONI Servo Drive Indigogo campaign.

    Started by jschulze‎, 03-19-2015 11:34 AM
    campaign, drive, indigogo, ioni, servo
    • Replies: 0
    • Views: 1,390
    03-19-2015, 11:34 AM Go to last post
  15. VSD-E USB Cable

    Started by francp111‎, 01-20-2015 10:09 AM
    already, buy, cable, granite, pin, serial, usb, vsd, vsd-e, work
    • Replies: 2
    • Views: 1,131
    03-12-2015, 05:07 PM Go to last post
    • Replies: 2
    • Views: 2,179
    03-12-2015, 11:04 AM Go to last post
  16. Granite VSD-XE tuning

    Started by richienz‎, 02-09-2015 05:16 PM
    cnc, forum, position, posts, tune
    • Replies: 8
    • Views: 1,515
    02-17-2015, 08:06 PM Go to last post

Page 1 of 11 1234 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 2 users browsing this forum. (0 members & 2 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands