Nakamura TW20 Parting Off
Registered
Nakamura TW20 Parting Off
Can anybody throw any light on parting off on Nakamura TW20 using parts catcher on sub spindle. Any help would be appreciated.
Redsid66 Similar Threads:
Member
I have an old program from a TW20 that has a cutoff op in it. But I'm not sure what you want. Do you want me to type up the relevant parts with the wait codes?
Registered
Hi extanker59
Any help at all would be appreciated. At the moment we are unsure how to get the sub-spindle across and the catcher in position to catch the part.
Regards
redsid66
Member
OK, here goes. I'm only going to post the relevant sections. Typing, so beware of typos.
%
:4811 (PART DESC)
(LEFT SIDE)
(430F SS, 1.25" DIA STK)
(STICKING OUT 1.95" MIN)
G0G28U0
M10(SAFETY COLLET CLOSE)
M41 (C AXIS DISENGAGE)
G50 S3500
M1
ROUGH FACE TURN
ETC
ECT
N5 (CUTOFF PICKOFF)
G0G28U0W0
M75 (RIGHT PROGRAM START)
T505G99G97S1500M3
X7.Z.015
M101
M102
M11
G4U.5
M103
M104
M10
G4U.5
G0S2500X1.35M6
G75P1000F.004X-.08
M105
M106
W.01
G0G28U0M7S500
Z1.95M5
/M98P9800 (LOAD BAR)
M30
%
i'LL POST SIDE 2 IN A FEW MINUTES. gETTING BUSY
Member
%
:4812 (PART DESC)
(RIGHT SIDE)
(PART HELD IN 1.25" COLLET)
(EJECTED OUT BY AIR AND EJECTOR)
G50S5500
G28U0W0
M14
M31
M97
M41
M74
M11
M84
M85
M1
N100(CUTOFF PICKOFF)
T200
M101
M96
G0G98W-20.15
G1G98W-1.26F25.
M10
G4U.75
M102
M103
G1G98W2.071F50.
M104
M105
G0G99W2.M97
M106
M3S2500
G0M15G28U0W0
M1
FACE
TURN ETC
N100(EJECT)
G4U.5
G0G28U0W0M5
M14
M73
M15
G4U.2
M11
G4U.2
M14 (AIR BLOW ON TO CLEAR COLLET OF CHIPS)
G4U.5
M74
M15
M31
M1
T200
M30
%
OK, thats it. do you need m code definitions?
Registered
Many thanks for your time. will try this at work tomorrow,and let you know the outcome. Once again many thanks.
Registered
All sorted, Many thanks extanker59 for all your help
Regards
redsid66
Member
Member
Re: Nakamura TW20 Parting Off
Hi
Have you tried sub-spindle transfer on a nakamura tome tw20
if so, could you please share the codes and procedure
i have tw20 1989 model with fanuc 0tc control
any help or pointers on this please
regards
Hemanth
Member
Re: Nakamura TW20 Parting Off
I will add something to this post. Fusion360 has a post processor - nakamura tome fanuc that works with the tw10 etc very well on the main spindle. It does not work on the sub. I am looking at this now...
cheers!
Nakamura TW20 Parting Off
Tags for this Thread
Posting Permissions
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
Forum Rules