General Material Machining Solutions

Page 1 of 31 123411 ... LastLast
Threads 1 to 20 of 601

Forum: General Material Machining Solutions

Discuss Material Machining Problems and Solutions Here.

  1. Need Help!- 400 Series Stainless bending after machining

    Started by jerry13‎, 02-20-2019 08:18 PM
    cutting, degree, side, sides, thick
    • Replies: 0
    • Views: 55
    02-20-2019, 08:18 PM Go to last post
  2. Feed and Speeds for ACM

    Started by treverinterstate‎, 02-20-2019 09:20 AM
    cut, feed, rate, sign, small
    • Replies: 0
    • Views: 66
    02-20-2019, 09:20 AM Go to last post
    • Replies: 0
    • Views: 15
    12-13-2018, 10:05 PM Go to last post
  3. Tooling Paste/Putty over Foam

    Started by drxlcarfreak‎, 11-29-2018 12:18 AM
    epoxy, machine, system, tooling, west
    • Replies: 7
    • Views: 364
    12-02-2018, 12:52 AM Go to last post
  4. Cutting S-Core

    Started by Groganeer‎, 02-20-2004 05:53 PM
    2 Pages
    1 2
    • Replies: 21
    • Views: 5,811
    11-13-2018, 03:26 AM Go to last post
  5. Need Help!- not sure what material to use

    Started by FUBAR62172‎, 10-26-2018 06:57 PM
    driller, material, mike, recommended, wondering
    • Replies: 1
    • Views: 192
    10-26-2018, 10:56 PM Go to last post
  6. Biodegradable Coolant Suggestions

    Started by AAYoung‎, 02-14-2018 06:09 PM
    biodegradable, cnc, coolant, cutting, salesman
    • Replies: 1
    • Views: 458
    10-22-2018, 05:26 PM Go to last post
  7. run g-code in inches on Laguna machine set for MM?

    Started by chris2112‎, 07-01-2018 07:59 PM
    g-code, inches, machine, run, set
    • Replies: 11
    • Views: 726
    10-22-2018, 08:16 AM Go to last post
  8. Need Help!- Milling Cast Iron

    Started by Khalid‎, 06-03-2010 01:12 PM
    6 Pages
    1 2 3 4 5 ... 6
    • Replies: 68
    • Views: 13,975
    10-13-2018, 10:31 AM Go to last post
  9. Need Help!- Newbie need help in pvc cutting

    Started by DanielSiew‎, 10-03-2018 03:44 AM
    • Replies: 1
    • Views: 175
    10-03-2018, 05:32 AM Go to last post
  10. Need Help!- I was told cutting PVC was nontoxic.

    Started by Jst187‎, 09-16-2018 10:22 PM
    4 Pages
    1 2 3 4
    • Replies: 45
    • Views: 1,119
    09-21-2018, 05:49 PM Go to last post
  11. Need Help!- Help calculating feeds/speeds

    Started by icecats‎, 08-12-2018 02:14 AM
    • Replies: 3
    • Views: 367
    09-04-2018, 11:41 AM Go to last post
    • Replies: 0
    • Views: 95
    09-03-2018, 09:07 AM Go to last post
  12. New to 4140 PH!

    Started by kreativjustin‎, 08-30-2018 02:36 PM
    cam, feeds, passes, software, work
    • Replies: 2
    • Views: 234
    08-31-2018, 06:32 AM Go to last post
  13. Need Help!- Grinder on lathe

    Started by Mr Bits‎, 07-20-2018 12:42 PM
    angle, bench, grinder, small, tools
    • Replies: 1
    • Views: 278
    07-20-2018, 09:54 PM Go to last post
    • Replies: 2
    • Views: 139
    07-19-2018, 04:40 PM Go to last post
  14. Speeds of Cut

    Started by Atomic_Sheep‎, 06-13-2018 12:11 PM
    basically, generate, heat, slower, tougher
    • Replies: 6
    • Views: 520
    06-25-2018, 12:51 PM Go to last post
  15. CNC Cookbooks F&S Calculator - How Good?

    Started by Atomic_Sheep‎, 06-13-2018 11:58 AM
    calculator, cnc, cookbooks, everyones, software
    • Replies: 2
    • Views: 247
    06-20-2018, 11:39 AM Go to last post
  16. Depth of Cut and Flute Length

    Started by Atomic_Sheep‎, 06-13-2018 08:50 AM
    cut, deep, depth, flute, half
    • Replies: 2
    • Views: 251
    06-14-2018, 04:19 AM Go to last post
  17. Can Keizen foam be CNC cut with a mill?

    Started by FoxCNC1‎, 12-09-2017 04:56 PM
    bit, cnc, recommend, tittle, tool
    • Replies: 2
    • Views: 363
    05-07-2018, 04:07 PM Go to last post

Page 1 of 31 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 10 users browsing this forum. (0 members & 10 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands