General Material Machining Solutions

Page 1 of 30 123411 ... LastLast
Threads 1 to 20 of 595

Forum: General Material Machining Solutions

Discuss Material Machining Problems and Solutions Here.

  1. Tooling Paste/Putty over Foam

    Started by drxlcarfreak‎, 11-29-2018 12:18 AM
    epoxy, machine, system, tooling, west
    • Replies: 7
    • Views: 194
    12-02-2018, 12:52 AM Go to last post
  2. Need Help!- not sure what material to use

    Started by FUBAR62172‎, 10-26-2018 06:57 PM
    driller, material, mike, recommended, wondering
    • Replies: 1
    • Views: 181
    10-26-2018, 10:56 PM Go to last post
  3. Biodegradable Coolant Suggestions

    Started by AAYoung‎, 02-14-2018 06:09 PM
    biodegradable, cnc, coolant, cutting, salesman
    • Replies: 1
    • Views: 437
    10-22-2018, 05:26 PM Go to last post
  4. run g-code in inches on Laguna machine set for MM?

    Started by chris2112‎, 07-01-2018 07:59 PM
    g-code, inches, machine, run, set
    • Replies: 11
    • Views: 655
    10-22-2018, 08:16 AM Go to last post
  5. Need Help!- Milling Cast Iron

    Started by Khalid‎, 06-03-2010 01:12 PM
    6 Pages
    1 2 3 4 5 ... 6
    • Replies: 68
    • Views: 13,836
    10-13-2018, 10:31 AM Go to last post
  6. Need Help!- Newbie need help in pvc cutting

    Started by DanielSiew‎, 10-03-2018 03:44 AM
    • Replies: 1
    • Views: 141
    10-03-2018, 05:32 AM Go to last post
  7. Need Help!- I was told cutting PVC was nontoxic.

    Started by Jst187‎, 09-16-2018 10:22 PM
    4 Pages
    1 2 3 4
    • Replies: 45
    • Views: 1,026
    09-21-2018, 05:49 PM Go to last post
  8. Need Help!- Help calculating feeds/speeds

    Started by icecats‎, 08-12-2018 02:14 AM
    • Replies: 3
    • Views: 352
    09-04-2018, 11:41 AM Go to last post
    • Replies: 0
    • Views: 89
    09-03-2018, 09:07 AM Go to last post
  9. New to 4140 PH!

    Started by kreativjustin‎, 08-30-2018 02:36 PM
    cam, feeds, passes, software, work
    • Replies: 2
    • Views: 214
    08-31-2018, 06:32 AM Go to last post
  10. Need Help!- Grinder on lathe

    Started by Mr Bits‎, 07-20-2018 12:42 PM
    angle, bench, grinder, small, tools
    • Replies: 1
    • Views: 268
    07-20-2018, 09:54 PM Go to last post
    • Replies: 2
    • Views: 129
    07-19-2018, 04:40 PM Go to last post
  11. Speeds of Cut

    Started by Atomic_Sheep‎, 06-13-2018 12:11 PM
    basically, generate, heat, slower, tougher
    • Replies: 6
    • Views: 507
    06-25-2018, 12:51 PM Go to last post
  12. CNC Cookbooks F&S Calculator - How Good?

    Started by Atomic_Sheep‎, 06-13-2018 11:58 AM
    calculator, cnc, cookbooks, everyones, software
    • Replies: 2
    • Views: 233
    06-20-2018, 11:39 AM Go to last post
  13. Depth of Cut and Flute Length

    Started by Atomic_Sheep‎, 06-13-2018 08:50 AM
    cut, deep, depth, flute, half
    • Replies: 2
    • Views: 233
    06-14-2018, 04:19 AM Go to last post
  14. Can Keizen foam be CNC cut with a mill?

    Started by FoxCNC1‎, 12-09-2017 04:56 PM
    bit, cnc, recommend, tittle, tool
    • Replies: 2
    • Views: 351
    05-07-2018, 04:07 PM Go to last post
    • Replies: 4
    • Views: 31,559
    05-02-2018, 12:02 PM Go to last post
  15. Newbie- Advice re Milling Aluminium

    Started by GaryWilliams‎, 11-10-2017 06:43 AM
    • Replies: 3
    • Views: 724
    01-22-2018, 03:14 AM Go to last post
  16. Need Help!- Question Running A286 hardened material on a Tsugami lathe

    Started by usalbeash‎, 01-04-2018 11:17 AM
    a286, hardened, inch, material, running
    • Replies: 0
    • Views: 279
    01-04-2018, 11:17 AM Go to last post
  17. Need Help!- Feedrate for Dibond

    Started by Organistrum‎, 12-25-2017 04:11 PM
    alu, dibond, feeds, speeds, success
    • Replies: 0
    • Views: 357
    12-25-2017, 04:11 PM Go to last post

Page 1 of 30 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 13 users browsing this forum. (0 members & 13 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands