General Material Machining Solutions

Page 1 of 31 123411 ... LastLast
Threads 1 to 20 of 602

Forum: General Material Machining Solutions

Discuss Material Machining Problems and Solutions Here.

  1. Variable frequency drives repair

    Started by DavidWilliams‎, 03-14-2019 06:16 AM
    repair vfds
    • Replies: 1
    • Views: 70
    03-21-2019, 03:04 AM Go to last post
  2. ACS355 Series VFDs

    Started by DavidWilliams‎, 03-02-2019 02:09 AM
    acs355 series vfds
    • Replies: 0
    • Views: 67
    03-02-2019, 02:09 AM Go to last post
  3. Need Help!- 400 Series Stainless bending after machining

    Started by jerry13‎, 02-20-2019 07:18 PM
    cutting, degree, side, sides, thick
    • Replies: 0
    • Views: 84
    02-20-2019, 07:18 PM Go to last post
  4. Feed and Speeds for ACM

    Started by treverinterstate‎, 02-20-2019 08:20 AM
    cut, feed, rate, sign, small
    • Replies: 0
    • Views: 91
    02-20-2019, 08:20 AM Go to last post
  5. Tooling Paste/Putty over Foam

    Started by drxlcarfreak‎, 11-28-2018 11:18 PM
    epoxy, machine, system, tooling, west
    • Replies: 7
    • Views: 398
    12-01-2018, 11:52 PM Go to last post
  6. Cutting S-Core

    Started by Groganeer‎, 02-20-2004 04:53 PM
    2 Pages
    1 2
    • Replies: 21
    • Views: 5,834
    11-13-2018, 02:26 AM Go to last post
  7. Need Help!- not sure what material to use

    Started by FUBAR62172‎, 10-26-2018 05:57 PM
    driller, material, mike, recommended, wondering
    • Replies: 1
    • Views: 199
    10-26-2018, 09:56 PM Go to last post
  8. Biodegradable Coolant Suggestions

    Started by AAYoung‎, 02-14-2018 05:09 PM
    biodegradable, cnc, coolant, cutting, salesman
    • Replies: 1
    • Views: 475
    10-22-2018, 04:26 PM Go to last post
  9. run g-code in inches on Laguna machine set for MM?

    Started by chris2112‎, 07-01-2018 06:59 PM
    g-code, inches, machine, run, set
    • Replies: 11
    • Views: 762
    10-22-2018, 07:16 AM Go to last post
  10. Need Help!- Milling Cast Iron

    Started by Khalid‎, 06-03-2010 12:12 PM
    6 Pages
    1 2 3 4 5 ... 6
    • Replies: 68
    • Views: 14,052
    10-13-2018, 09:31 AM Go to last post
  11. Need Help!- Newbie need help in pvc cutting

    Started by DanielSiew‎, 10-03-2018 02:44 AM
    • Replies: 1
    • Views: 186
    10-03-2018, 04:32 AM Go to last post
  12. Need Help!- I was told cutting PVC was nontoxic.

    Started by Jst187‎, 09-16-2018 09:22 PM
    4 Pages
    1 2 3 4
    • Replies: 45
    • Views: 1,164
    09-21-2018, 04:49 PM Go to last post
  13. Need Help!- Help calculating feeds/speeds

    Started by icecats‎, 08-12-2018 01:14 AM
    • Replies: 3
    • Views: 385
    09-04-2018, 10:41 AM Go to last post
    • Replies: 0
    • Views: 107
    09-03-2018, 08:07 AM Go to last post
  14. New to 4140 PH!

    Started by kreativjustin‎, 08-30-2018 01:36 PM
    cam, feeds, passes, software, work
    • Replies: 2
    • Views: 244
    08-31-2018, 05:32 AM Go to last post
  15. Need Help!- Grinder on lathe

    Started by Mr Bits‎, 07-20-2018 11:42 AM
    angle, bench, grinder, small, tools
    • Replies: 1
    • Views: 287
    07-20-2018, 08:54 PM Go to last post
    • Replies: 2
    • Views: 147
    07-19-2018, 03:40 PM Go to last post
  16. Speeds of Cut

    Started by Atomic_Sheep‎, 06-13-2018 11:11 AM
    basically, generate, heat, slower, tougher
    • Replies: 6
    • Views: 530
    06-25-2018, 11:51 AM Go to last post
  17. CNC Cookbooks F&S Calculator - How Good?

    Started by Atomic_Sheep‎, 06-13-2018 10:58 AM
    calculator, cnc, cookbooks, everyones, software
    • Replies: 2
    • Views: 261
    06-20-2018, 10:39 AM Go to last post
  18. Depth of Cut and Flute Length

    Started by Atomic_Sheep‎, 06-13-2018 07:50 AM
    cut, deep, depth, flute, half
    • Replies: 2
    • Views: 264
    06-14-2018, 03:19 AM Go to last post

Page 1 of 31 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 7 users browsing this forum. (0 members & 7 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands