General Material Machining Solutions

Page 1 of 30 123411 ... LastLast
Threads 1 to 20 of 592

Forum: General Material Machining Solutions

Discuss Material Machining Problems and Solutions Here.

  1. Need Help!- I was told cutting PVC was nontoxic.

    Started by Jst187‎, 09-16-2018 09:22 PM
    3 Pages
    1 2 3
    • Replies: 24
    • Views: 328
    Today, 12:25 AM Go to last post
  2. run g-code in inches on Laguna machine set for MM?

    Started by chris2112‎, 07-01-2018 06:59 PM
    g-code, inches, machine, run, set
    • Replies: 8
    • Views: 535
    09-04-2018, 03:07 PM Go to last post
  3. Need Help!- Help calculating feeds/speeds

    Started by icecats‎, 08-12-2018 01:14 AM
    • Replies: 3
    • Views: 300
    09-04-2018, 10:41 AM Go to last post
    • Replies: 0
    • Views: 70
    09-03-2018, 08:07 AM Go to last post
  4. New to 4140 PH!

    Started by kreativjustin‎, 08-30-2018 01:36 PM
    cam, feeds, passes, software, work
    • Replies: 2
    • Views: 159
    08-31-2018, 05:32 AM Go to last post
  5. Need Help!- Grinder on lathe

    Started by Mr Bits‎, 07-20-2018 11:42 AM
    angle, bench, grinder, small, tools
    • Replies: 1
    • Views: 244
    07-20-2018, 08:54 PM Go to last post
    • Replies: 2
    • Views: 110
    07-19-2018, 03:40 PM Go to last post
  6. Speeds of Cut

    Started by Atomic_Sheep‎, 06-13-2018 11:11 AM
    basically, generate, heat, slower, tougher
    • Replies: 6
    • Views: 467
    06-25-2018, 11:51 AM Go to last post
  7. CNC Cookbooks F&S Calculator - How Good?

    Started by Atomic_Sheep‎, 06-13-2018 10:58 AM
    calculator, cnc, cookbooks, everyones, software
    • Replies: 2
    • Views: 211
    06-20-2018, 10:39 AM Go to last post
  8. Depth of Cut and Flute Length

    Started by Atomic_Sheep‎, 06-13-2018 07:50 AM
    cut, deep, depth, flute, half
    • Replies: 2
    • Views: 195
    06-14-2018, 03:19 AM Go to last post
  9. Can Keizen foam be CNC cut with a mill?

    Started by FoxCNC1‎, 12-09-2017 03:56 PM
    bit, cnc, recommend, tittle, tool
    • Replies: 2
    • Views: 320
    05-07-2018, 03:07 PM Go to last post
    • Replies: 4
    • Views: 31,021
    05-02-2018, 11:02 AM Go to last post
  10. Biodegradable Coolant Suggestions

    Started by AAYoung‎, 02-14-2018 05:09 PM
    biodegradable, cnc, coolant, cutting, salesman
    • Replies: 0
    • Views: 381
    02-14-2018, 05:09 PM Go to last post
  11. Newbie- Advice re Milling Aluminium

    Started by GaryWilliams‎, 11-10-2017 05:43 AM
    • Replies: 3
    • Views: 683
    01-22-2018, 02:14 AM Go to last post
  12. Need Help!- Question Running A286 hardened material on a Tsugami lathe

    Started by usalbeash‎, 01-04-2018 10:17 AM
    a286, hardened, inch, material, running
    • Replies: 0
    • Views: 265
    01-04-2018, 10:17 AM Go to last post
  13. Need Help!- Feedrate for Dibond

    Started by Organistrum‎, 12-25-2017 03:11 PM
    alu, dibond, feeds, speeds, success
    • Replies: 0
    • Views: 290
    12-25-2017, 03:11 PM Go to last post
  14. Question Q: Deep (~9") Drilling Speeds & Feeds

    Started by thinkless‎, 12-13-2017 01:35 PM
    cutting feed, deep drills, drilling, feeds, speeds
    • Replies: 1
    • Views: 359
    12-14-2017, 12:21 PM Go to last post
  15. Newbie- Mitre fold realy thick board

    Started by tricud‎, 11-25-2017 08:22 AM
    • Replies: 1
    • Views: 306
    11-25-2017, 08:52 AM Go to last post
  16. Just In Cutting fiber cement sheet

    Started by Junaidzia‎, 11-07-2017 01:37 PM
    sheet, cutting, cement, fiber, note
    • Replies: 9
    • Views: 632
    11-09-2017, 06:23 PM Go to last post
  17. Micro Machining with 0.1mm dia cutter any one?

    Started by Zuedog‎, 10-29-2017 05:33 PM
    • Replies: 3
    • Views: 350
    10-30-2017, 02:15 PM Go to last post

Page 1 of 30 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 6 users browsing this forum. (0 members & 6 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands