PaperStone

Results 1 to 6 of 6

Thread: PaperStone

  1. #1
    cpnagle_cnc's Avatar
    Join Date
    Jan 2021
    Posts
    7
    Downloads
    0
    Uploads
    0

    Default PaperStone

    I'm fairly new to cnc routing PaperStone. Currently using Vortex Tool #3135 (De Viper) "1/2 Compression bit. It cuts just fine however the PaperStone material is a very strong material and turns out is quite abrasive/hard on tooling. Cutting between 6-8 sheets before the bit becomes dull and needing replacement. Just curious what other peoples experience with PaperStone is and what they use for tooling? Thanks



  2. #2
    Member awerby's Avatar
    Join Date
    Apr 2004
    Posts
    5728
    Downloads
    0
    Uploads
    0

    Default Re: PaperStone

    It's a solid material; ;why are you using a compression bit? That's usually used because you don't want to disrupt the veneers of plywood. An ordinary upcut bit would probably work fine in paperstone. You might try a diamond-coated bit if the abrasion factor is a big issue for you.

    [FONT=Verdana]Andrew Werby[/FONT]
    [URL="http://www.computersculpture.com/"]Website[/URL]


  3. #3
    cpnagle_cnc's Avatar
    Join Date
    Jan 2021
    Posts
    7
    Downloads
    0
    Uploads
    0

    Default Re: PaperStone

    Well it is what the company I work for was using to the best of their knowledge before I was hired. I mean the compression bit leaves a clean cut edge. Paperstone in my limited experience with it so far I have noticed it can chip on the edges just a bit, so perhaps that is why they were using a compression bit idk. And yes we just ordered and tried a new (PCD) Diamond Coated Compression bit yesterday, seemed to work great but the key is how long will it last. Thank you for your input Andrew.



  4. #4
    Member awerby's Avatar
    Join Date
    Apr 2004
    Posts
    5728
    Downloads
    0
    Uploads
    0

    Default Re: PaperStone

    Let us know how much cutting you get out of that PCD-coated tool, and how much it cost versus the uncoated version - I know they stay sharp longer, but not if it's really worth the extra cost (if you don't value your time spent changing bits, anyway).

    [FONT=Verdana]Andrew Werby[/FONT]
    [URL="http://www.computersculpture.com/"]Website[/URL]


  5. #5
    Member ger21's Avatar
    Join Date
    Mar 2003
    Location
    Shelby Township
    Posts
    35538
    Downloads
    1
    Uploads
    0

    Default Re: PaperStone

    I've only cut Paperstone once or twice in the past, but if cutting a lot of it, I'd try an Amana DRB-208 or similar.
    I use them when I need to cut a lot of abrasive materials, as they'll last 10x longer than carbide.

    Gerry

    UCCNC 2017 Screenset
    [URL]http://www.thecncwoodworker.com/2017.html[/URL]

    Mach3 2010 Screenset
    [URL]http://www.thecncwoodworker.com/2010.html[/URL]

    JointCAM - CNC Dovetails & Box Joints
    [URL]http://www.g-forcecnc.com/jointcam.html[/URL]

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  6. #6
    cpnagle_cnc's Avatar
    Join Date
    Jan 2021
    Posts
    7
    Downloads
    0
    Uploads
    0

    Default Re: PaperStone

    The PCD-200 tool only lasted 8 cuts before I started to see cut quality begin to diminish. Soon after I realized we were running that tool way too fast according to manufacturers feed rate recommendations. Gonna try a new bit, same one but at 140ipm, we were running 200-300.



Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

PaperStone

PaperStone