Add Laser to my existing DIY CNC


Results 1 to 6 of 6

Thread: Add Laser to my existing DIY CNC

  1. #1
    Gold Member Mr.Chips's Avatar
    Join Date
    Sep 2003
    Location
    Gilbert Az
    Posts
    1460
    Downloads
    0
    Uploads
    0

    Default Add Laser to my existing DIY CNC

    Mach 3,ESS controller board, Gecko 540 stepper controller.
    I built my CNC over 12 years ago and am ready to add a laser engraver to its capabilities.

    A few years ago I purchased a simple laser set up with PS but no way to control the power or the on/off cycle. So all I have done with it was to plug it in once and it does power on.

    PS PRODUCT DETAILS:
    CCDSTAR, Model EZ-1225 2018B,
    INPUT: 100-240VAC
    OUTPUT: DC 12 V 2.5A

    LASER MODULE:
    Model FA02
    PS 12VDC
    DRIVE MODE: internal ACC
    WAVE LENGTH 445 nm
    OPTICAL POWER 2500mW
    SN. 1804EPXZ

    All I want to use this for is laser etching, and I would like to do this without removing any of my present CNC controller system shown above.

    Is this add on possible to my existing system, and how to integrate/ wire it up.

    Thanks
    Hager

    Similar Threads:


  2. #2
    Member
    Join Date
    Nov 2008
    Location
    USA
    Posts
    623
    Downloads
    0
    Uploads
    0

    Default Re: Add Laser to my existing DIY CNC

    In order to fire a laser you send it an on/off signal and a PWM signal. PWM drives the laser power. What input signals exist on your FA02?
    Then you need to output signals from the G540. And control those outputs in Mach. Neither one is set up for controlling a laser.
    I would recommend you look at GRBL controllers.


    Sent from my iPhone using Tapatalk



  3. #3
    Gold Member Mr.Chips's Avatar
    Join Date
    Sep 2003
    Location
    Gilbert Az
    Posts
    1460
    Downloads
    0
    Uploads
    0

    Default Re: Add Laser to my existing DIY CNC

    Quote Originally Posted by Dean448 View Post
    In order to fire a laser you send it an on/off signal and a PWM signal. PWM drives the laser power. What input signals exist on your FA02?
    Then you need to output signals from the G540. And control those outputs in Mach. Neither one is set up for controlling a laser.
    I would recommend you look at GRBL controllers.


    Sent from my iPhone using Tapatalk
    Thanks Dean, but that’s exactly what I don’t want to do.
    My four steppers, X,Yslave, Y master, and Z are wired to the G540, which is plugged into the ESS SMOOTH STEPPER.
    The limit and homing switches are wired to the C25S which plugs into the ESS SMOOTH STEPPER

    Are you saying I don’t the the right kind of input/output ports?

    What is FA02?

    I understand that I do need a Laser Controller Board, I think could it could be controlled be the input/output C25S board.

    Thanks



  4. #4
    Member awerby's Avatar
    Join Date
    Apr 2004
    Posts
    5579
    Downloads
    0
    Uploads
    0

    Default Re: Add Laser to my existing DIY CNC

    Be careful; even a laser pointer can damage your eyes; these cutting lasers are a lot more dangerous. You may be thinking of engraving a piece of aluminum; it can treat that like a mirror and bounce the beam back at you. That's why every commercial laser cutter has a full enclosure with door switches to ensure the power is out when you open it. Please keep safety top of mind when adding a laser to your CNC machine.

    [FONT=Verdana]Andrew Werby[/FONT]
    [URL="http://www.computersculpture.com/"]Website[/URL]


  5. #5
    Member
    Join Date
    Nov 2008
    Location
    USA
    Posts
    623
    Downloads
    0
    Uploads
    0

    Default Re: Add Laser to my existing DIY CNC

    Your correct, the smoothstepper has some laser functionality. No clue how good it is or easy to make anything with.

    I’ve seen many posts where folks want to use their router as a laser engraver. It’s like using a cnc router and trying to make it a 3d printer. You might be able to get it to do some things but it’s not designed to be a laser cutting/engraving. And your laser diode is very inexpensive so I’m not sure what your going to get out of it.

    Why don’t you think about building a CO2 laser cutter? You will find that it has many uses compared to that laser diode that is more like a toy.


    Sent from my iPhone using Tapatalk



  6. #6
    Gold Member Mr.Chips's Avatar
    Join Date
    Sep 2003
    Location
    Gilbert Az
    Posts
    1460
    Downloads
    0
    Uploads
    0

    Default Re: Add Laser to my existing DIY CNC

    Quote Originally Posted by Dean448 View Post
    Your correct, the smoothstepper has some laser functionality. No clue how good it is or easy to make anything with.

    I’ve seen many posts where folks want to use their router as a laser engraver. It’s like using a cnc router and trying to make it a 3d printer. You might be able to get it to do some things but it’s not designed to be a laser cutting/engraving. And your laser diode is very inexpensive so I’m not sure what your going to get out of it.

    Why don’t you think about building a CO2 laser cutter? You will find that it has many uses compared to that laser diode that is more like a toy.


    Sent from my iPhone using Tapatalk
    Not interested in cutting material, just some putting some fine text on some projects.

    Hopefully someone can give me some tips on laser engraving using the majority of components I have.
    Thanks
    Haget



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Add Laser to my existing DIY CNC

Add Laser to my existing DIY CNC

Add Laser to my existing DIY CNC