General EDM Discussion


Page 1 of 34 123411 ... LastLast
Threads 1 to 20 of 673

Forum: General EDM Discussion

Discuss building, operating EDM machines here!

  1. Sodick Short Circuit Error

    Started by GlennV‎, Yesterday 09:30 PM
    • Replies: 1
    • Views: 48
    Today, 08:05 AM Go to last post
  2. Charmilles Robofil 510f contact block spacer

    Started by nsnipe‎, 08-12-2022 08:09 AM
    510f, charmilles, contact block, robofil, spacer
    • Replies: 0
    • Views: 74
    08-12-2022, 08:09 AM Go to last post
  3. Need Help!- MITSUBISHI DWC 90SZ

    Started by CHARLY90‎, 08-11-2022 07:02 PM
    90sz, alarm, dwc, rally, thermal
    • Replies: 0
    • Views: 79
    08-11-2022, 07:02 PM Go to last post
  4. Question Agie Elox Mondo 20 Futura II

    Started by Losrios‎, 08-09-2022 11:32 AM
    fix, futura, hour, problem, screen
    • Replies: 1
    • Views: 101
    08-09-2022, 03:28 PM Go to last post
  5. Need Help!- Agie Elox Mondo 30 | error message E6

    Started by Fermin_Rivera‎, 08-05-2022 03:44 PM
    agie, elox, error, message, mondo
    • Replies: 0
    • Views: 139
    08-05-2022, 03:44 PM Go to last post
  6. Cutting taper with Fanuc Robocut

    Started by tlmkr38‎, 01-19-2022 07:11 AM
    • Replies: 10
    • Views: 674
    08-01-2022, 03:27 PM Go to last post
  7. Idea Agie Charmilles 440cc vs Mitsubishi FA20 Wire EDM

    Started by Renexila‎, 07-21-2022 04:27 PM
    agie, charmilles, mitshubishi fa20, robofil 440cc, wire edm
    • Replies: 0
    • Views: 174
    07-21-2022, 04:27 PM Go to last post
  8. Agie Charmilles 440cc vs Mitsubishi FA20 Wire EDM

    Started by Renexila‎, 07-21-2022 02:07 PM
    agie wire edm, wire edm mitsubishi
    • Replies: 0
    • Views: 37
    07-21-2022, 02:07 PM Go to last post
  9. Need Help!- Fanuc Robocut alpha A01B edm power doesn't start.

    Started by steryd‎, 07-15-2022 05:21 PM
    edm, generator, occured, start, turning
    • Replies: 1
    • Views: 192
    07-20-2022, 12:41 PM Go to last post
  10. Problem- Eltee HELP

    Started by Mosnarde‎, 07-14-2022 06:52 PM
    appreciated, find, looked, manual, tram
    • Replies: 0
    • Views: 143
    07-14-2022, 06:52 PM Go to last post
  11. Need Help!- Robofil 690 Genrator Configuration and service Password

    Started by violeypa‎, 06-13-2022 02:04 PM
    • Replies: 0
    • Views: 347
    06-13-2022, 02:04 PM Go to last post
  12. HANVEDTH WORKMAN EDM

    Started by gabedrummin‎, 06-13-2022 07:53 AM
    edge, edm, head, move, touching
    • Replies: 0
    • Views: 211
    06-13-2022, 07:53 AM Go to last post
  13. Charmilles Roboform 30 need help with setup!

    Started by SecondOps‎, 06-08-2022 06:58 PM
    charmilles, offset, roboform, time, tool
    • Replies: 0
    • Views: 276
    06-08-2022, 06:58 PM Go to last post
  14. Question Mitsubishi MV2400 R Taper/Axis movement Issues

    Started by StellarSkyFall‎, 06-16-2021 11:19 PM
    machinist, mitsubishi, software, wire edm, year
    • Replies: 2
    • Views: 772
    06-07-2022, 02:21 PM Go to last post
  15. Problem- Cutting punch on Robofil EDM

    Started by xal3r‎, 05-25-2022 01:43 AM
    cut, cutting, mastercam, punch, tabs
    • Replies: 0
    • Views: 271
    05-25-2022, 01:43 AM Go to last post
    • Replies: 0
    • Views: 195
    05-24-2022, 02:06 PM Go to last post
  16. Eltee users left?

    Started by claya‎, 05-19-2022 02:32 PM
    advice, eltee, estimate, times, users
    • Replies: 0
    • Views: 155
    05-19-2022, 02:32 PM Go to last post
  17. Need Help!- Fanuc Robocut G codes

    Started by Knapke‎, 05-13-2022 06:32 AM
    fanuc, machine, multiple, robocut, zeros
    • Replies: 0
    • Views: 255
    05-13-2022, 06:32 AM Go to last post
  18. Need Help!- Fanuc Robocut alpha oc wire edm backlash compansation

    Started by shabbirabbas‎, 01-28-2019 08:52 AM
    • Replies: 2
    • Views: 1,806
    05-12-2022, 08:04 PM Go to last post

Page 1 of 34 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 8 users browsing this forum. (0 members & 8 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands