General EDM Discussion


Page 1 of 31 123411 ... LastLast
Threads 1 to 20 of 609

Forum: General EDM Discussion

Discuss building, operating EDM machines here!

  1. Need Help!- AGIE 150 HSS hard disk died.

    Started by skeumhc‎, 05-01-2021 09:20 PM
    agie, died, disk, hard, software
    • Replies: 0
    • Views: 79
    05-01-2021, 09:20 PM Go to last post
  2. Robofil 290 start up issue

    Started by Bloodwinghunter‎, 08-08-2019 03:15 PM
    boxes, find, robofil, stuff, usb
    • Replies: 3
    • Views: 1,005
    04-28-2021, 08:45 AM Go to last post
  3. Need Help!- Makino U53K Wire EDM help

    Started by Skidoo900‎, 04-05-2021 05:58 PM
    makino, u53k, wedm, wire edm
    • Replies: 0
    • Views: 2,221
    04-05-2021, 05:58 PM Go to last post
  4. Need Help!- load System 3 in sodick A530D

    Started by hotrunner‎, 05-19-2015 02:23 PM
    • Replies: 2
    • Views: 1,508
    03-29-2021, 08:15 AM Go to last post
    • Replies: 0
    • Views: 329
    03-11-2021, 07:46 AM Go to last post
  5. Newbie- charmille robofil 510

    Started by rgailhac‎, 03-07-2021 07:36 AM
    catia, charmille, postpro, robofil, software
    • Replies: 0
    • Views: 202
    03-07-2021, 07:36 AM Go to last post
  6. Need Help!- Mitsubishi FX20 contact problem

    Started by Pete_MP_Mold‎, 11-15-2016 11:57 PM
    • Replies: 5
    • Views: 1,051
    02-21-2021, 11:53 AM Go to last post
  7. Exclamation SODICK WIRE EDM MARK 21

    Started by BKCOM‎, 12-23-2008 11:18 AM
    2 Pages
    1 2
    • Replies: 23
    • Views: 27,240
    02-20-2021, 03:03 AM Go to last post
  8. SAXON EDM DOCUMENTATION

    Started by mousongie‎, 02-13-2021 04:58 AM
    documentation, edm, find, machine, saxon
    • Replies: 0
    • Views: 284
    02-13-2021, 04:58 AM Go to last post
  9. Problem- Problem Sodick LN1W

    Started by tecnorobi‎, 02-10-2021 02:17 AM
    • Replies: 1
    • Views: 274
    02-11-2021, 04:59 AM Go to last post
  10. Problem- Sodick MM3 sinker EDM control will not power on

    Started by mctaylor82‎, 02-09-2021 05:59 PM
    • Replies: 0
    • Views: 230
    02-09-2021, 05:59 PM Go to last post
  11. sodick A530 error ErR:Vr

    Started by hotrunner‎, 02-08-2021 09:01 PM
    • Replies: 0
    • Views: 299
    02-08-2021, 09:01 PM Go to last post
  12. Sodick A320D with EX21

    Started by janczar84‎, 02-07-2021 12:36 PM
    • Replies: 0
    • Views: 151
    02-07-2021, 12:36 PM Go to last post
    • Replies: 10
    • Views: 4,547
    02-04-2021, 02:57 PM Go to last post
  13. Elox-Fanuc wire cut series Q Issue

    Started by ddfoe‎, 12-12-2020 12:08 PM
    • Replies: 8
    • Views: 354
    02-03-2021, 11:16 AM Go to last post
  14. Lightbulb Need Help!- Agie 200D with strange behavior !!!

    Started by Claytronics‎, 10-31-2019 09:14 AM
    200d, agie, error, short cirtuit, wire
    • Replies: 1
    • Views: 821
    01-01-2021, 04:43 PM Go to last post
  15. Charmilles Robofil 200 startup

    Started by Shawn Lucas‎, 05-12-2010 06:17 PM
    3 Pages
    1 2 3
    • Replies: 43
    • Views: 17,919
    12-31-2020, 04:36 PM Go to last post
  16. Newbie- Fanuc Robocut alpha oc

    Started by BRAIN-HURTS‎, 12-16-2020 06:03 AM
    alpha, fanuc, ideas, lubricate, robocut
    • Replies: 0
    • Views: 406
    12-16-2020, 06:03 AM Go to last post
  17. Robofil 310 Startup problems

    Started by jptech‎, 11-26-2020 06:28 PM
    machine, robofil, run, software, voltage
    • Replies: 0
    • Views: 438
    11-26-2020, 06:28 PM Go to last post
  18. Need Help!- MOLYBDENUM EDM FLUID

    Started by KristyKC‎, 11-18-2020 11:32 AM
    film, fluid, machine, molybdenum, wire
    • Replies: 0
    • Views: 352
    11-18-2020, 11:32 AM Go to last post

Page 1 of 31 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 29 users browsing this forum. (0 members & 29 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands