General CNC Plasma / Oxy Fuel Cutting Machines


Page 1 of 62 12341151 ... LastLast
Threads 1 to 20 of 1232

Forum: General CNC Plasma / Oxy Fuel Cutting Machines

CNC Plasma and Oxy Fuel Cutting Machines

    • Replies: 6
    • Views: 75
    Yesterday, 10:03 PM Go to last post
  1. Post Need Help!- Mach3 THC301d input and output pin numbers

    Started by 50sCarStuff‎, Yesterday 06:15 PM
    mach3 plasma pins, plasma, texas microcircuit, thc301, thc301d
    • Replies: 0
    • Views: 39
    Yesterday, 06:15 PM Go to last post
  2. Moved: Need Help!- E.O.C.a code / E.O.C/n Code

    Started by melliotardelli‎, Yesterday 02:51 PM
    •  
    •  
  3. Anouncement regarding plasma and Linuxcnc

    Started by tommylight‎, 08-01-2019 04:32 PM
    • Replies: 13
    • Views: 2,755
    10-12-2021, 09:51 PM Go to last post
  4. A Different Machine - Downdraft/water table

    Started by flyinwilly‎, 06-14-2010 10:38 PM
    6 Pages
    1 2 3 4 5 ... 6
    • Replies: 103
    • Views: 36,619
    10-02-2021, 09:46 AM Go to last post
  5. New Machine Build- Would like opinion(s) about floating Z

    Started by zappafan1‎, 09-21-2021 11:20 PM
    afford, cnc, floating, start, time
    • Replies: 0
    • Views: 157
    09-21-2021, 11:20 PM Go to last post
  6. Best way to get a 100:1 arc voltage out of Powermax 85

    Started by SSOKIE‎, 09-17-2021 08:00 AM
    board, divider, find, powermax, signal
    • Replies: 1
    • Views: 212
    09-18-2021, 02:24 AM Go to last post
  7. Plasma cutting problem

    Started by MoeRadwan‎, 09-14-2021 07:03 AM
    • Replies: 1
    • Views: 140
    09-14-2021, 07:22 AM Go to last post
    • Replies: 4
    • Views: 268
    09-05-2021, 04:28 AM Go to last post
  8. i'm looking for lantek expert v 27

    Started by agiorgos‎, 10-14-2010 04:00 PM
    lantek expert, v27
    • Replies: 18
    • Views: 20,965
    08-03-2021, 12:40 PM Go to last post
  9. Need Help!- Hypertherm D80 Cant connect to host computer

    Started by Jesse_c20‎, 07-29-2021 10:18 AM
    cnc, computer, hypertherm, koike, predator editor
    • Replies: 1
    • Views: 273
    07-29-2021, 11:26 AM Go to last post
  10. Plasma Controller

    Started by BenoitMyrand‎, 01-24-2021 12:10 AM
    cnc, control, height, software, torch
    • Replies: 7
    • Views: 1,133
    07-23-2021, 08:48 PM Go to last post
  11. Need Help!- Plasma/ Router table

    Started by ECaseyP‎, 07-11-2021 09:01 PM
    build, cnc, plasma, plasma table build, table
    • Replies: 4
    • Views: 539
    07-12-2021, 07:47 PM Go to last post
  12. Need Help!- Need a recommendation on a control board for plasma cutter

    Started by tas99‎, 06-27-2021 03:50 PM
    board, control, cutter, height, recommendations
    • Replies: 3
    • Views: 583
    06-29-2021, 09:00 AM Go to last post
  13. Need Help!- My plasma torch not moving up and down..HYD-THC XPTHC-4H

    Started by dharnishpatel‎, 08-03-2018 03:13 PM
    • Replies: 5
    • Views: 2,645
    06-08-2021, 11:53 PM Go to last post
  14. Need Help!- Torch keeps going on and off repeatedly

    Started by saadsallaq‎, 06-08-2021 04:57 AM
    clicking, cutter, repeatedly, solenoid, torch
    • Replies: 0
    • Views: 256
    06-08-2021, 04:57 AM Go to last post
  15. Need Help!- SH-HC31 THC install

    Started by KPB‎, 11-12-2020 11:45 PM
    cnc, controller, plasma, table, thc
    • Replies: 3
    • Views: 897
    06-06-2021, 05:35 AM Go to last post
  16. STV SparX4800 CNC - Nevada - What a ride!

    Started by tchadwyk‎, 04-25-2021 01:52 PM
    cnc, experience, small, software, stv
    • Replies: 2
    • Views: 605
    05-23-2021, 05:40 PM Go to last post
  17. RZNC 0501 Baileigh PT 44 plasma controller issue

    Started by phaefner‎, 05-22-2021 11:53 AM
    • Replies: 0
    • Views: 263
    05-22-2021, 11:53 AM Go to last post
  18. Post Need Help!- Adding Hypertherm THC Sensor to a Burny 3 control

    Started by MgW1‎, 05-12-2021 11:32 AM
    burny, control, hypertherm, sensor, thc
    • Replies: 0
    • Views: 396
    05-12-2021, 11:32 AM Go to last post

Page 1 of 62 12341151 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 12 users browsing this forum. (0 members & 12 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands