General CNC Plasma / Oxy Fuel Cutting Machines


Page 1 of 62 12341151 ... LastLast
Threads 1 to 20 of 1221

Forum: General CNC Plasma / Oxy Fuel Cutting Machines

CNC Plasma and Oxy Fuel Cutting Machines

  1. Post Need Help!- Adding Hypertherm THC Sensor to a Burny 3 control

    Started by MgW1‎, 05-12-2021 11:32 AM
    burny, control, hypertherm, sensor, thc
    • Replies: 0
    • Views: 141
    05-12-2021, 11:32 AM Go to last post
  2. Hypertherm 260XD won't arc on

    Started by gts16774‎, 05-02-2021 04:17 PM
    • Replies: 0
    • Views: 536
    05-02-2021, 04:17 PM Go to last post
  3. STV SparX4800 CNC - Nevada - What a ride!

    Started by tchadwyk‎, 04-25-2021 01:52 PM
    cnc, experience, small, software, stv
    • Replies: 1
    • Views: 279
    04-25-2021, 03:13 PM Go to last post
  4. Need Help!- problem with burny phantom mnt -13720

    Started by walid2525‎, 04-19-2021 06:23 PM
    burny, cnc, idea, machine, problem
    • Replies: 1
    • Views: 172
    04-20-2021, 06:48 PM Go to last post
  5. Question What is Corner/Ext Ref?

    Started by maudib32‎, 04-20-2021 02:54 PM
    • Replies: 0
    • Views: 89
    04-20-2021, 02:54 PM Go to last post
  6. Need Help!- THC Proma 150 Problems

    Started by stevenquinn34‎, 04-18-2021 09:13 PM
    arc, lights, terminals, thc, voltage
    • Replies: 0
    • Views: 262
    04-18-2021, 09:13 PM Go to last post
  7. Need Help!- CNC STUCK IN OXYGEN FUEL AND WONT SWITCH BACK TO PLASMA.

    Started by chrisf2001‎, 04-11-2021 02:48 PM
    cnc, fuel, oxygen, plasma, stuck
    • Replies: 2
    • Views: 314
    04-12-2021, 04:35 AM Go to last post
  8. Use an older hypertherm 900 or buy new

    Started by deyzin‎, 04-12-2021 12:22 AM
    buy, cnc, duramax, machine, torch
    • Replies: 0
    • Views: 186
    04-12-2021, 12:22 AM Go to last post
  9. Shop Sabre plasma

    Started by Hexheadart‎, 03-17-2021 08:08 AM
    shop sabre plasma table
    • Replies: 1
    • Views: 1,582
    03-21-2021, 09:05 AM Go to last post
  10. Plasma controller kit

    Started by VE360‎, 03-11-2021 11:19 PM
    cnc, controller, i’m, kit, sheet
    • Replies: 2
    • Views: 404
    03-18-2021, 06:14 AM Go to last post
  11. Help!

    Started by Geosmi‎, 03-16-2021 10:37 PM
    circle, edges, george, rounded, upload
    • Replies: 1
    • Views: 256
    03-17-2021, 04:43 PM Go to last post
  12. Need Help!- Starfire program

    Started by J_perez17‎, 03-16-2021 04:17 PM
    • Replies: 0
    • Views: 221
    03-16-2021, 04:17 PM Go to last post
  13. australian plasma cnc builders i need your advice

    Started by deano_pamela‎, 03-14-2021 03:26 PM
    australia, cnc plasma
    • Replies: 0
    • Views: 186
    03-14-2021, 03:26 PM Go to last post
  14. AXBB-E Controller and Closed Loop Nema 34 Motors

    Started by GCable‎, 03-12-2021 02:54 PM
    cnc, diy, isolated ports, plasma, software
    • Replies: 2
    • Views: 290
    03-13-2021, 10:49 AM Go to last post
  15. Question Torch Height Control advice

    Started by Dogpound‎, 03-09-2021 04:42 PM
    cnc, table, thc, torch, torch height controller
    • Replies: 0
    • Views: 272
    03-09-2021, 04:42 PM Go to last post
    • Replies: 0
    • Views: 171
    03-05-2021, 05:14 PM Go to last post
  16. Newbie- Mg Industries

    Started by Ricoch3T‎, 03-02-2021 04:19 PM
    controller, found, program, serial, upload
    • Replies: 0
    • Views: 251
    03-02-2021, 04:19 PM Go to last post
  17. Plasma Controller

    Started by BenoitMyrand‎, 01-24-2021 12:10 AM
    cnc, control, height, software, torch
    • Replies: 5
    • Views: 643
    03-02-2021, 03:44 AM Go to last post
  18. Question Help - Get interference from Plasma on my PC

    Started by nicjac‎, 09-15-2007 07:51 AM
    mos
    • Replies: 17
    • Views: 13,475
    03-02-2021, 02:42 AM Go to last post

Page 1 of 62 12341151 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 17 users browsing this forum. (0 members & 17 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands