General CNC Plasma / Oxy Fuel Cutting Machines


Page 1 of 62 12341151 ... LastLast
Threads 1 to 20 of 1229

Forum: General CNC Plasma / Oxy Fuel Cutting Machines

CNC Plasma and Oxy Fuel Cutting Machines

  1. New Machine Build- Would like opinion(s) about floating Z

    Started by zappafan1‎, 09-21-2021 11:20 PM
    afford, cnc, floating, start, time
    • Replies: 0
    • Views: 52
    09-21-2021, 11:20 PM Go to last post
  2. Best way to get a 100:1 arc voltage out of Powermax 85

    Started by SSOKIE‎, 09-17-2021 08:00 AM
    board, divider, find, powermax, signal
    • Replies: 1
    • Views: 120
    09-18-2021, 02:24 AM Go to last post
  3. Plasma cutting problem

    Started by MoeRadwan‎, 09-14-2021 07:03 AM
    • Replies: 1
    • Views: 89
    09-14-2021, 07:22 AM Go to last post
    • Replies: 4
    • Views: 214
    09-05-2021, 04:28 AM Go to last post
  4. i'm looking for lantek expert v 27

    Started by agiorgos‎, 10-14-2010 04:00 PM
    lantek expert, v27
    • Replies: 18
    • Views: 20,735
    08-03-2021, 12:40 PM Go to last post
  5. Need Help!- Hypertherm D80 Cant connect to host computer

    Started by Jesse_c20‎, 07-29-2021 10:18 AM
    cnc, computer, hypertherm, koike, predator editor
    • Replies: 1
    • Views: 230
    07-29-2021, 11:26 AM Go to last post
  6. Plasma Controller

    Started by BenoitMyrand‎, 01-24-2021 12:10 AM
    cnc, control, height, software, torch
    • Replies: 7
    • Views: 1,071
    07-23-2021, 08:48 PM Go to last post
  7. Need Help!- Plasma/ Router table

    Started by ECaseyP‎, 07-11-2021 09:01 PM
    build, cnc, plasma, plasma table build, table
    • Replies: 4
    • Views: 481
    07-12-2021, 07:47 PM Go to last post
  8. Need Help!- Need a recommendation on a control board for plasma cutter

    Started by tas99‎, 06-27-2021 03:50 PM
    board, control, cutter, height, recommendations
    • Replies: 3
    • Views: 528
    06-29-2021, 09:00 AM Go to last post
  9. Need Help!- My plasma torch not moving up and down..HYD-THC XPTHC-4H

    Started by dharnishpatel‎, 08-03-2018 03:13 PM
    • Replies: 5
    • Views: 2,558
    06-08-2021, 11:53 PM Go to last post
  10. Need Help!- Torch keeps going on and off repeatedly

    Started by saadsallaq‎, 06-08-2021 04:57 AM
    clicking, cutter, repeatedly, solenoid, torch
    • Replies: 0
    • Views: 229
    06-08-2021, 04:57 AM Go to last post
  11. Need Help!- SH-HC31 THC install

    Started by KPB‎, 11-12-2020 11:45 PM
    cnc, controller, plasma, table, thc
    • Replies: 3
    • Views: 855
    06-06-2021, 05:35 AM Go to last post
  12. STV SparX4800 CNC - Nevada - What a ride!

    Started by tchadwyk‎, 04-25-2021 01:52 PM
    cnc, experience, small, software, stv
    • Replies: 2
    • Views: 576
    05-23-2021, 05:40 PM Go to last post
  13. RZNC 0501 Baileigh PT 44 plasma controller issue

    Started by phaefner‎, 05-22-2021 11:53 AM
    • Replies: 0
    • Views: 250
    05-22-2021, 11:53 AM Go to last post
  14. Post Need Help!- Adding Hypertherm THC Sensor to a Burny 3 control

    Started by MgW1‎, 05-12-2021 11:32 AM
    burny, control, hypertherm, sensor, thc
    • Replies: 0
    • Views: 374
    05-12-2021, 11:32 AM Go to last post
  15. Hypertherm 260XD won't arc on

    Started by gts16774‎, 05-02-2021 04:17 PM
    • Replies: 0
    • Views: 711
    05-02-2021, 04:17 PM Go to last post
  16. Need Help!- problem with burny phantom mnt -13720

    Started by walid2525‎, 04-19-2021 06:23 PM
    burny, cnc, idea, machine, problem
    • Replies: 1
    • Views: 387
    04-20-2021, 06:48 PM Go to last post
  17. Question What is Corner/Ext Ref?

    Started by maudib32‎, 04-20-2021 02:54 PM
    • Replies: 0
    • Views: 240
    04-20-2021, 02:54 PM Go to last post
  18. Need Help!- THC Proma 150 Problems

    Started by stevenquinn34‎, 04-18-2021 09:13 PM
    arc, lights, terminals, thc, voltage
    • Replies: 0
    • Views: 454
    04-18-2021, 09:13 PM Go to last post

Page 1 of 62 12341151 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 11 users browsing this forum. (0 members & 11 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands