General CNC Plasma / Oxy Fuel Cutting Machines


Page 1 of 62 12341151 ... LastLast
Threads 1 to 20 of 1235

Forum: General CNC Plasma / Oxy Fuel Cutting Machines

CNC Plasma and Oxy Fuel Cutting Machines

  1. Question Problem- Old Saw Blade Not Conductive Enough?

    Started by raygussy‎, 01-18-2022 06:33 PM
    blade, idea, made, multimeter, students
    • Replies: 1
    • Views: 79
    Yesterday, 02:01 AM Go to last post
  2. Hypertherm ht2000 error code

    Started by Dem1‎, 09-06-2019 07:08 PM
    code, error, ht2000, hypertherm, problem
    • Replies: 1
    • Views: 874
    01-17-2022, 04:00 PM Go to last post
  3. Need Help!- Burnt 2.5 with CMC replicator 1000

    Started by CMGriffin‎, 01-15-2022 03:01 PM
    burnt, cmc, red, replicator, scanner
    • Replies: 0
    • Views: 84
    01-15-2022, 03:01 PM Go to last post
  4. What to Charge for Plasma Cutting Services

    Started by rescueweasel‎, 10-03-2010 09:52 PM
    2 Pages
    1 2
    • Replies: 22
    • Views: 50,836
    01-11-2022, 09:35 AM Go to last post
  5. Post Need Help!- Mach3 THC301d input and output pin numbers

    Started by 50sCarStuff‎, 10-20-2021 07:15 PM
    mach3 plasma pins, plasma, texas microcircuit, thc301, thc301d
    • Replies: 1
    • Views: 288
    01-07-2022, 10:19 PM Go to last post
  6. Need Help!- SH-HC31 THC install

    Started by KPB‎, 11-13-2020 12:45 AM
    cnc, controller, plasma, table, thc
    • Replies: 4
    • Views: 1,081
    01-04-2022, 11:45 AM Go to last post
    • Replies: 0
    • Views: 417
    11-07-2021, 01:32 AM Go to last post
  7. Can't cut accurate circles - Any Ideas what to try next?

    Started by turbotoys‎, 10-20-2021 05:31 PM
    2 Pages
    1 2
    • Replies: 23
    • Views: 959
    10-27-2021, 06:02 PM Go to last post
  8. Moved: Need Help!- E.O.C.a code / E.O.C/n Code

    Started by melliotardelli‎, 10-20-2021 03:51 PM
    •  
    •  
  9. Anouncement regarding plasma and Linuxcnc

    Started by tommylight‎, 08-01-2019 05:32 PM
    • Replies: 13
    • Views: 3,216
    10-12-2021, 10:51 PM Go to last post
  10. A Different Machine - Downdraft/water table

    Started by flyinwilly‎, 06-14-2010 11:38 PM
    6 Pages
    1 2 3 4 5 ... 6
    • Replies: 103
    • Views: 37,178
    10-02-2021, 10:46 AM Go to last post
  11. New Machine Build- Would like opinion(s) about floating Z

    Started by zappafan1‎, 09-22-2021 12:20 AM
    afford, cnc, floating, start, time
    • Replies: 0
    • Views: 278
    09-22-2021, 12:20 AM Go to last post
  12. Best way to get a 100:1 arc voltage out of Powermax 85

    Started by SSOKIE‎, 09-17-2021 09:00 AM
    board, divider, find, powermax, signal
    • Replies: 1
    • Views: 362
    09-18-2021, 03:24 AM Go to last post
  13. Plasma cutting problem

    Started by MoeRadwan‎, 09-14-2021 08:03 AM
    • Replies: 1
    • Views: 212
    09-14-2021, 08:22 AM Go to last post
    • Replies: 4
    • Views: 359
    09-05-2021, 05:28 AM Go to last post
  14. i'm looking for lantek expert v 27

    Started by agiorgos‎, 10-14-2010 05:00 PM
    lantek expert, v27
    • Replies: 18
    • Views: 21,644
    08-03-2021, 01:40 PM Go to last post
  15. Need Help!- Hypertherm D80 Cant connect to host computer

    Started by Jesse_c20‎, 07-29-2021 11:18 AM
    cnc, computer, hypertherm, koike, predator editor
    • Replies: 1
    • Views: 328
    07-29-2021, 12:26 PM Go to last post
  16. Plasma Controller

    Started by BenoitMyrand‎, 01-24-2021 01:10 AM
    cnc, control, height, software, torch
    • Replies: 7
    • Views: 1,303
    07-23-2021, 09:48 PM Go to last post
  17. Need Help!- Plasma/ Router table

    Started by ECaseyP‎, 07-11-2021 10:01 PM
    build, cnc, plasma, plasma table build, table
    • Replies: 4
    • Views: 665
    07-12-2021, 08:47 PM Go to last post
  18. Need Help!- Need a recommendation on a control board for plasma cutter

    Started by tas99‎, 06-27-2021 04:50 PM
    board, control, cutter, height, recommendations
    • Replies: 3
    • Views: 724
    06-29-2021, 10:00 AM Go to last post

Page 1 of 62 12341151 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 20 users browsing this forum. (0 members & 20 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands