General CNC Plasma / Oxy Fuel Cutting Machines


Page 1 of 59 12341151 ... LastLast
Threads 1 to 20 of 1164

Forum: General CNC Plasma / Oxy Fuel Cutting Machines

CNC Plasma and Oxy Fuel Cutting Machines

  1. Proma Plasma Controller with THC - New

    Started by NSchlee‎, 10-04-2019 06:49 PM
    controller, neal, plasma, proma, thc
    • Replies: 3
    • Views: 1,329
    09-20-2020, 06:30 AM Go to last post
  2. New Machine Build- Looking for some input to my design.

    Started by philofab‎, 08-17-2020 11:07 PM
    • Replies: 14
    • Views: 413
    09-12-2020, 06:12 PM Go to last post
  3. Need Help!- CNC plasma setup. Lots of questions.

    Started by Jim Dawson‎, 08-16-2020 04:02 PM
    2 Pages
    1 2
    • Replies: 28
    • Views: 813
    08-29-2020, 04:50 PM Go to last post
  4. Mixing steppers and servos on same machine?

    Started by philofab‎, 08-12-2020 03:37 PM
    • Replies: 7
    • Views: 276
    08-17-2020, 11:02 PM Go to last post
  5. Question Has anyone used a Langmuir crossfire

    Started by Jordan3991‎, 05-29-2019 08:34 PM
    • Replies: 2
    • Views: 864
    08-14-2020, 12:11 PM Go to last post
    • Replies: 0
    • Views: 122
    08-06-2020, 01:30 AM Go to last post
  6. Help with THC wired and setup

    Started by gamaz7‎, 01-04-2019 07:48 PM
    cnc, connect, plasma, thc, working
    • Replies: 1
    • Views: 734
    08-05-2020, 10:41 PM Go to last post
  7. Build Thread- Review - My Arclight ArcrPro 12000 CNC Plasma

    Started by BarnFab‎, 10-02-2012 07:37 PM
    2 Pages
    1 2
    almost, asking, far, goes, hypertherm powermax 85, its, look, mos, next, powermax 85, then
    • Replies: 23
    • Views: 15,404
    08-04-2020, 02:28 PM Go to last post
  8. Question DIY torch height control

    Started by mjp‎, 11-19-2007 10:27 PM
    2 Pages
    1 2
    • Replies: 37
    • Views: 74,245
    07-30-2020, 08:16 AM Go to last post
  9. Burny 3 controller problems..Help!

    Started by Welderpaul‎, 06-08-2012 05:17 PM
    its, newish, saw, then
    • Replies: 14
    • Views: 9,545
    07-25-2020, 10:34 AM Go to last post
  10. Burny 3 CNC Path Error

    Started by East123‎, 07-25-2020 10:33 AM
    burny3 cnc
    • Replies: 0
    • Views: 115
    07-25-2020, 10:33 AM Go to last post
  11. Lantek

    Started by scott24‎, 04-05-2011 03:09 AM
    onto, say, then
    • Replies: 9
    • Views: 8,400
    07-22-2020, 01:55 AM Go to last post
  12. Esab ultrarex with nce 290, 320 ,520 stering

    Started by Bad_boym‎, 01-18-2020 02:16 PM
    • Replies: 12
    • Views: 431
    07-21-2020, 10:25 AM Go to last post
    • Replies: 2
    • Views: 391
    07-19-2020, 11:05 AM Go to last post
  13. Esab nce 290 floppy boot problem

    Started by ray6171‎, 07-17-2020 09:06 AM
    boot floppy esab nce
    • Replies: 0
    • Views: 123
    07-17-2020, 09:06 AM Go to last post
  14. Esab controller NCE 390

    Started by Dem1‎, 09-08-2019 07:37 AM
    drives, esab, floppy, nce, running
    • Replies: 6
    • Views: 847
    07-17-2020, 07:30 AM Go to last post
  15. Need Help!- Upgrade

    Started by pjsbird‎, 07-13-2020 12:58 PM
    blaze, plasmaroute, table, upgrade
    • Replies: 0
    • Views: 173
    07-13-2020, 12:58 PM Go to last post
  16. Pronest Post Processor CFF File

    Started by cah‎, 07-13-2020 11:50 AM
    cff, file, post, processor, pronest
    • Replies: 0
    • Views: 478
    07-13-2020, 11:50 AM Go to last post
  17. Need Help!- Plasma torch stops before cut is ready

    Started by d3workz‎, 07-10-2020 04:17 PM
    cnc, command, cut, ready, wrong
    • Replies: 0
    • Views: 144
    07-10-2020, 04:17 PM Go to last post
  18. Replace cebora torch with hypertherm

    Started by gyvara_gy‎, 07-07-2020 10:50 AM
    cebora, replacement, torch
    • Replies: 0
    • Views: 126
    07-07-2020, 10:50 AM Go to last post

Page 1 of 59 12341151 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 22 users browsing this forum. (0 members & 22 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands