General CNC Plasma / Oxy Fuel Cutting Machines


Page 1 of 61 12341151 ... LastLast
Threads 1 to 20 of 1220

Forum: General CNC Plasma / Oxy Fuel Cutting Machines

CNC Plasma and Oxy Fuel Cutting Machines

  1. Hypertherm 260XD won't arc on

    Started by gts16774‎, 05-02-2021 04:17 PM
    • Replies: 0
    • Views: 163
    05-02-2021, 04:17 PM Go to last post
  2. STV SparX4800 CNC - Nevada - What a ride!

    Started by tchadwyk‎, 04-25-2021 01:52 PM
    cnc, experience, small, software, stv
    • Replies: 1
    • Views: 246
    04-25-2021, 03:13 PM Go to last post
  3. Need Help!- problem with burny phantom mnt -13720

    Started by walid2525‎, 04-19-2021 06:23 PM
    burny, cnc, idea, machine, problem
    • Replies: 1
    • Views: 147
    04-20-2021, 06:48 PM Go to last post
  4. Question What is Corner/Ext Ref?

    Started by maudib32‎, 04-20-2021 02:54 PM
    • Replies: 0
    • Views: 71
    04-20-2021, 02:54 PM Go to last post
  5. Need Help!- THC Proma 150 Problems

    Started by stevenquinn34‎, 04-18-2021 09:13 PM
    arc, lights, terminals, thc, voltage
    • Replies: 0
    • Views: 248
    04-18-2021, 09:13 PM Go to last post
  6. Need Help!- CNC STUCK IN OXYGEN FUEL AND WONT SWITCH BACK TO PLASMA.

    Started by chrisf2001‎, 04-11-2021 02:48 PM
    cnc, fuel, oxygen, plasma, stuck
    • Replies: 2
    • Views: 294
    04-12-2021, 04:35 AM Go to last post
  7. Use an older hypertherm 900 or buy new

    Started by deyzin‎, 04-12-2021 12:22 AM
    buy, cnc, duramax, machine, torch
    • Replies: 0
    • Views: 161
    04-12-2021, 12:22 AM Go to last post
  8. Shop Sabre plasma

    Started by Hexheadart‎, 03-17-2021 08:08 AM
    shop sabre plasma table
    • Replies: 1
    • Views: 1,561
    03-21-2021, 09:05 AM Go to last post
  9. Plasma controller kit

    Started by VE360‎, 03-11-2021 11:19 PM
    cnc, controller, i’m, kit, sheet
    • Replies: 2
    • Views: 377
    03-18-2021, 06:14 AM Go to last post
  10. Help!

    Started by Geosmi‎, 03-16-2021 10:37 PM
    circle, edges, george, rounded, upload
    • Replies: 1
    • Views: 239
    03-17-2021, 04:43 PM Go to last post
  11. Need Help!- Starfire program

    Started by J_perez17‎, 03-16-2021 04:17 PM
    • Replies: 0
    • Views: 194
    03-16-2021, 04:17 PM Go to last post
  12. australian plasma cnc builders i need your advice

    Started by deano_pamela‎, 03-14-2021 03:26 PM
    australia, cnc plasma
    • Replies: 0
    • Views: 164
    03-14-2021, 03:26 PM Go to last post
  13. AXBB-E Controller and Closed Loop Nema 34 Motors

    Started by GCable‎, 03-12-2021 02:54 PM
    cnc, diy, isolated ports, plasma, software
    • Replies: 2
    • Views: 274
    03-13-2021, 10:49 AM Go to last post
  14. Question Torch Height Control advice

    Started by Dogpound‎, 03-09-2021 04:42 PM
    cnc, table, thc, torch, torch height controller
    • Replies: 0
    • Views: 247
    03-09-2021, 04:42 PM Go to last post
    • Replies: 0
    • Views: 156
    03-05-2021, 05:14 PM Go to last post
  15. Newbie- Mg Industries

    Started by Ricoch3T‎, 03-02-2021 04:19 PM
    controller, found, program, serial, upload
    • Replies: 0
    • Views: 228
    03-02-2021, 04:19 PM Go to last post
  16. Plasma Controller

    Started by BenoitMyrand‎, 01-24-2021 12:10 AM
    cnc, control, height, software, torch
    • Replies: 5
    • Views: 627
    03-02-2021, 03:44 AM Go to last post
  17. Question Help - Get interference from Plasma on my PC

    Started by nicjac‎, 09-15-2007 07:51 AM
    mos
    • Replies: 17
    • Views: 13,424
    03-02-2021, 02:42 AM Go to last post
  18. Unhappy CNC Plasma Interference Issue - Flashcut Problems

    Started by andyleahy1‎, 03-01-2021 01:18 PM
    cnc plasma interference, emi plasma, flashcut plasma, grounding, rf noise
    • Replies: 1
    • Views: 240
    03-01-2021, 09:53 PM Go to last post

Page 1 of 61 12341151 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 11 users browsing this forum. (0 members & 11 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands