General CNC Plasma / Oxy Fuel Cutting Machines


Page 1 of 61 12341151 ... LastLast
Threads 1 to 20 of 1219

Forum: General CNC Plasma / Oxy Fuel Cutting Machines

CNC Plasma and Oxy Fuel Cutting Machines

  1. STV SparX4800 CNC - Nevada - What a ride!

    Started by tchadwyk‎, 04-25-2021 01:52 PM
    cnc, experience, small, software, stv
    • Replies: 1
    • Views: 229
    04-25-2021, 03:13 PM Go to last post
  2. Need Help!- problem with burny phantom mnt -13720

    Started by walid2525‎, 04-19-2021 06:23 PM
    burny, cnc, idea, machine, problem
    • Replies: 1
    • Views: 140
    04-20-2021, 06:48 PM Go to last post
  3. Question What is Corner/Ext Ref?

    Started by maudib32‎, 04-20-2021 02:54 PM
    • Replies: 0
    • Views: 67
    04-20-2021, 02:54 PM Go to last post
  4. Need Help!- THC Proma 150 Problems

    Started by stevenquinn34‎, 04-18-2021 09:13 PM
    arc, lights, terminals, thc, voltage
    • Replies: 0
    • Views: 245
    04-18-2021, 09:13 PM Go to last post
  5. Need Help!- CNC STUCK IN OXYGEN FUEL AND WONT SWITCH BACK TO PLASMA.

    Started by chrisf2001‎, 04-11-2021 02:48 PM
    cnc, fuel, oxygen, plasma, stuck
    • Replies: 2
    • Views: 286
    04-12-2021, 04:35 AM Go to last post
  6. Use an older hypertherm 900 or buy new

    Started by deyzin‎, 04-12-2021 12:22 AM
    buy, cnc, duramax, machine, torch
    • Replies: 0
    • Views: 151
    04-12-2021, 12:22 AM Go to last post
  7. Shop Sabre plasma

    Started by Hexheadart‎, 03-17-2021 08:08 AM
    shop sabre plasma table
    • Replies: 1
    • Views: 1,558
    03-21-2021, 09:05 AM Go to last post
  8. Plasma controller kit

    Started by VE360‎, 03-11-2021 11:19 PM
    cnc, controller, i’m, kit, sheet
    • Replies: 2
    • Views: 368
    03-18-2021, 06:14 AM Go to last post
  9. Help!

    Started by Geosmi‎, 03-16-2021 10:37 PM
    circle, edges, george, rounded, upload
    • Replies: 1
    • Views: 237
    03-17-2021, 04:43 PM Go to last post
  10. Need Help!- Starfire program

    Started by J_perez17‎, 03-16-2021 04:17 PM
    • Replies: 0
    • Views: 190
    03-16-2021, 04:17 PM Go to last post
  11. australian plasma cnc builders i need your advice

    Started by deano_pamela‎, 03-14-2021 03:26 PM
    australia, cnc plasma
    • Replies: 0
    • Views: 160
    03-14-2021, 03:26 PM Go to last post
  12. AXBB-E Controller and Closed Loop Nema 34 Motors

    Started by GCable‎, 03-12-2021 02:54 PM
    cnc, diy, isolated ports, plasma, software
    • Replies: 2
    • Views: 272
    03-13-2021, 10:49 AM Go to last post
  13. Question Torch Height Control advice

    Started by Dogpound‎, 03-09-2021 04:42 PM
    cnc, table, thc, torch, torch height controller
    • Replies: 0
    • Views: 243
    03-09-2021, 04:42 PM Go to last post
    • Replies: 0
    • Views: 154
    03-05-2021, 05:14 PM Go to last post
  14. Newbie- Mg Industries

    Started by Ricoch3T‎, 03-02-2021 04:19 PM
    controller, found, program, serial, upload
    • Replies: 0
    • Views: 222
    03-02-2021, 04:19 PM Go to last post
  15. Plasma Controller

    Started by BenoitMyrand‎, 01-24-2021 12:10 AM
    cnc, control, height, software, torch
    • Replies: 5
    • Views: 621
    03-02-2021, 03:44 AM Go to last post
  16. Question Help - Get interference from Plasma on my PC

    Started by nicjac‎, 09-15-2007 07:51 AM
    mos
    • Replies: 17
    • Views: 13,419
    03-02-2021, 02:42 AM Go to last post
  17. Unhappy CNC Plasma Interference Issue - Flashcut Problems

    Started by andyleahy1‎, 03-01-2021 01:18 PM
    cnc plasma interference, emi plasma, flashcut plasma, grounding, rf noise
    • Replies: 1
    • Views: 238
    03-01-2021, 09:53 PM Go to last post
  18. Moved: CNC cutting air

    Started by shaka3zulu4‎, 02-28-2021 09:23 PM
    •  
    •  

Page 1 of 61 12341151 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 7 users browsing this forum. (0 members & 7 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands