General CNC Plasma / Oxy Fuel Cutting Machines


Page 1 of 59 12341151 ... LastLast
Threads 1 to 20 of 1175

Forum: General CNC Plasma / Oxy Fuel Cutting Machines

CNC Plasma and Oxy Fuel Cutting Machines

  1. CNC issues

    Started by PlamaWORX‎, Yesterday 08:08 PM
    • Replies: 0
    • Views: 53
    Yesterday, 08:08 PM Go to last post
    • Replies: 1
    • Views: 133
    10-25-2020, 11:55 PM Go to last post
  2. Size air source for plasma CNC

    Started by koenbro‎, 10-21-2020 02:42 PM
    • Replies: 2
    • Views: 179
    10-23-2020, 02:21 PM Go to last post
  3. Some free stuff for plasma people

    Started by Albert2020‎, 10-19-2020 10:23 AM
    cad, finished, free, plasma, youtube
    • Replies: 0
    • Views: 258
    10-19-2020, 10:23 AM Go to last post
  4. Need Help!- Suggestions for DIY Plasma Tube Cutter - University Capstone Project

    Started by Xyphota‎, 10-17-2020 08:06 PM
    cnc, cutter, engineering, machine, tube
    • Replies: 6
    • Views: 245
    10-18-2020, 11:15 PM Go to last post
  5. New Machine Build- Help for first CNC Plasma design

    Started by Pedro_Bs_As‎, 10-04-2020 10:19 PM
    cnc, design help, forum, new at cnc, plasma build
    • Replies: 4
    • Views: 322
    10-10-2020, 05:14 PM Go to last post
  6. Just In new cam software for plasma

    Started by Albert2020‎, 10-07-2020 12:31 PM
    cam, folder, plasma, software, working
    • Replies: 1
    • Views: 202
    10-08-2020, 02:11 AM Go to last post
  7. Need Help!- Kjellberg flow control problem

    Started by Aldoc‎, 10-01-2020 01:51 PM
    flow control, gas flow, kjellberg, pgc, pgv
    • Replies: 0
    • Views: 161
    10-01-2020, 01:51 PM Go to last post
  8. Need help with THC PlasmaSensOut

    Started by damorus‎, 09-30-2020 06:39 AM
    cnc, masso, output, plasmasensout, thc
    • Replies: 0
    • Views: 138
    09-30-2020, 06:39 AM Go to last post
  9. What to Charge for Plasma Cutting Services

    Started by rescueweasel‎, 10-03-2010 08:52 PM
    • Replies: 19
    • Views: 45,833
    09-24-2020, 06:08 PM Go to last post
  10. Need Help!- Multicam Plasma Trouble

    Started by Mart1298‎, 09-21-2020 06:35 AM
    calls, multicam, plasma, trouble, years
    • Replies: 1
    • Views: 175
    09-21-2020, 02:05 PM Go to last post
  11. Proma Plasma Controller with THC - New

    Started by NSchlee‎, 10-04-2019 06:49 PM
    controller, neal, plasma, proma, thc
    • Replies: 3
    • Views: 1,488
    09-20-2020, 06:30 AM Go to last post
  12. New Machine Build- Looking for some input to my design.

    Started by philofab‎, 08-17-2020 11:07 PM
    • Replies: 14
    • Views: 538
    09-12-2020, 06:12 PM Go to last post
  13. Need Help!- CNC plasma setup. Lots of questions.

    Started by Jim Dawson‎, 08-16-2020 04:02 PM
    2 Pages
    1 2
    • Replies: 28
    • Views: 1,027
    08-29-2020, 04:50 PM Go to last post
  14. Mixing steppers and servos on same machine?

    Started by philofab‎, 08-12-2020 03:37 PM
    • Replies: 7
    • Views: 308
    08-17-2020, 11:02 PM Go to last post
  15. Question Has anyone used a Langmuir crossfire

    Started by Jordan3991‎, 05-29-2019 08:34 PM
    • Replies: 2
    • Views: 925
    08-14-2020, 12:11 PM Go to last post
    • Replies: 0
    • Views: 140
    08-06-2020, 01:30 AM Go to last post
  16. Help with THC wired and setup

    Started by gamaz7‎, 01-04-2019 07:48 PM
    cnc, connect, plasma, thc, working
    • Replies: 1
    • Views: 777
    08-05-2020, 10:41 PM Go to last post
  17. Build Thread- Review - My Arclight ArcrPro 12000 CNC Plasma

    Started by BarnFab‎, 10-02-2012 07:37 PM
    2 Pages
    1 2
    almost, asking, far, goes, hypertherm powermax 85, its, look, mos, next, powermax 85, then
    • Replies: 23
    • Views: 15,577
    08-04-2020, 02:28 PM Go to last post
  18. Question DIY torch height control

    Started by mjp‎, 11-19-2007 10:27 PM
    2 Pages
    1 2
    • Replies: 37
    • Views: 74,611
    07-30-2020, 08:16 AM Go to last post

Page 1 of 59 12341151 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 15 users browsing this forum. (0 members & 15 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands