General CNC Plasma / Oxy Fuel Cutting Machines


Page 1 of 61 12341151 ... LastLast
Threads 1 to 20 of 1214

Forum: General CNC Plasma / Oxy Fuel Cutting Machines

CNC Plasma and Oxy Fuel Cutting Machines

  1. Need Help!- CNC STUCK IN OXYGEN FUEL AND WONT SWITCH BACK TO PLASMA.

    Started by chrisf2001‎, 04-11-2021 02:48 PM
    cnc, fuel, oxygen, plasma, stuck
    • Replies: 2
    • Views: 152
    Yesterday, 04:35 AM Go to last post
  2. Use an older hypertherm 900 or buy new

    Started by deyzin‎, Yesterday 12:22 AM
    buy, cnc, duramax, machine, torch
    • Replies: 0
    • Views: 75
    Yesterday, 12:22 AM Go to last post
  3. Shop Sabre plasma

    Started by Hexheadart‎, 03-17-2021 08:08 AM
    shop sabre plasma table
    • Replies: 1
    • Views: 1,483
    03-21-2021, 09:05 AM Go to last post
  4. Plasma controller kit

    Started by VE360‎, 03-11-2021 11:19 PM
    cnc, controller, i’m, kit, sheet
    • Replies: 2
    • Views: 305
    03-18-2021, 06:14 AM Go to last post
  5. Help!

    Started by Geosmi‎, 03-16-2021 10:37 PM
    circle, edges, george, rounded, upload
    • Replies: 1
    • Views: 200
    03-17-2021, 04:43 PM Go to last post
  6. Need Help!- Starfire program

    Started by J_perez17‎, 03-16-2021 04:17 PM
    • Replies: 0
    • Views: 140
    03-16-2021, 04:17 PM Go to last post
  7. australian plasma cnc builders i need your advice

    Started by deano_pamela‎, 03-14-2021 03:26 PM
    australia, cnc plasma
    • Replies: 0
    • Views: 118
    03-14-2021, 03:26 PM Go to last post
  8. AXBB-E Controller and Closed Loop Nema 34 Motors

    Started by GCable‎, 03-12-2021 02:54 PM
    cnc, diy, isolated ports, plasma, software
    • Replies: 2
    • Views: 224
    03-13-2021, 10:49 AM Go to last post
  9. Question Torch Height Control advice

    Started by Dogpound‎, 03-09-2021 04:42 PM
    cnc, table, thc, torch, torch height controller
    • Replies: 0
    • Views: 193
    03-09-2021, 04:42 PM Go to last post
    • Replies: 0
    • Views: 117
    03-05-2021, 05:14 PM Go to last post
  10. Newbie- Mg Industries

    Started by Ricoch3T‎, 03-02-2021 04:19 PM
    controller, found, program, serial, upload
    • Replies: 0
    • Views: 183
    03-02-2021, 04:19 PM Go to last post
  11. Plasma Controller

    Started by BenoitMyrand‎, 01-24-2021 12:10 AM
    cnc, control, height, software, torch
    • Replies: 5
    • Views: 559
    03-02-2021, 03:44 AM Go to last post
  12. Question Help - Get interference from Plasma on my PC

    Started by nicjac‎, 09-15-2007 07:51 AM
    mos
    • Replies: 17
    • Views: 13,298
    03-02-2021, 02:42 AM Go to last post
  13. Unhappy CNC Plasma Interference Issue - Flashcut Problems

    Started by andyleahy1‎, 03-01-2021 01:18 PM
    cnc plasma interference, emi plasma, flashcut plasma, grounding, rf noise
    • Replies: 1
    • Views: 194
    03-01-2021, 09:53 PM Go to last post
  14. Moved: CNC cutting air

    Started by shaka3zulu4‎, 02-28-2021 09:23 PM
    •  
    •  
  15. Not cutting out part correctly

    Started by bhagie‎, 02-28-2021 09:55 AM
    • Replies: 1
    • Views: 170
    02-28-2021, 01:43 PM Go to last post
  16. Need Help!- Plasma Table Manufacturer Vanished, what now?

    Started by Fyresparxx‎, 02-22-2021 11:38 AM
    apparently, manufacturer, plasma, table, vanished
    • Replies: 3
    • Views: 341
    02-24-2021, 11:45 AM Go to last post
  17. CNC plasma torch interchangeabilty

    Started by JohnDeere630‎, 02-21-2021 08:14 PM
    cnc, forum, ipt, torch, torches
    • Replies: 2
    • Views: 252
    02-22-2021, 04:23 PM Go to last post
    • Replies: 17
    • Views: 17,662
    02-15-2021, 09:04 AM Go to last post
  18. CandCNC Plasma, Bladerunner, Mach3

    Started by JohnPrevost‎, 02-13-2021 05:02 PM
    control, i’m, light, mach3, serial
    • Replies: 0
    • Views: 346
    02-13-2021, 05:02 PM Go to last post

Page 1 of 61 12341151 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 48 users browsing this forum. (0 members & 48 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands