General CNC Plasma / Oxy Fuel Cutting Machines


Page 1 of 62 12341151 ... LastLast
Threads 1 to 20 of 1233

Forum: General CNC Plasma / Oxy Fuel Cutting Machines

CNC Plasma and Oxy Fuel Cutting Machines

    • Replies: 0
    • Views: 209
    11-07-2021, 01:32 AM Go to last post
  1. Can't cut accurate circles - Any Ideas what to try next?

    Started by turbotoys‎, 10-20-2021 05:31 PM
    2 Pages
    1 2
    • Replies: 23
    • Views: 801
    10-27-2021, 06:02 PM Go to last post
  2. Post Need Help!- Mach3 THC301d input and output pin numbers

    Started by 50sCarStuff‎, 10-20-2021 07:15 PM
    mach3 plasma pins, plasma, texas microcircuit, thc301, thc301d
    • Replies: 0
    • Views: 146
    10-20-2021, 07:15 PM Go to last post
  3. Moved: Need Help!- E.O.C.a code / E.O.C/n Code

    Started by melliotardelli‎, 10-20-2021 03:51 PM
    •  
    •  
  4. Anouncement regarding plasma and Linuxcnc

    Started by tommylight‎, 08-01-2019 05:32 PM
    • Replies: 13
    • Views: 2,992
    10-12-2021, 10:51 PM Go to last post
  5. A Different Machine - Downdraft/water table

    Started by flyinwilly‎, 06-14-2010 11:38 PM
    6 Pages
    1 2 3 4 5 ... 6
    • Replies: 103
    • Views: 36,892
    10-02-2021, 10:46 AM Go to last post
  6. New Machine Build- Would like opinion(s) about floating Z

    Started by zappafan1‎, 09-22-2021 12:20 AM
    afford, cnc, floating, start, time
    • Replies: 0
    • Views: 216
    09-22-2021, 12:20 AM Go to last post
  7. Best way to get a 100:1 arc voltage out of Powermax 85

    Started by SSOKIE‎, 09-17-2021 09:00 AM
    board, divider, find, powermax, signal
    • Replies: 1
    • Views: 273
    09-18-2021, 03:24 AM Go to last post
  8. Plasma cutting problem

    Started by MoeRadwan‎, 09-14-2021 08:03 AM
    • Replies: 1
    • Views: 172
    09-14-2021, 08:22 AM Go to last post
    • Replies: 4
    • Views: 309
    09-05-2021, 05:28 AM Go to last post
  9. i'm looking for lantek expert v 27

    Started by agiorgos‎, 10-14-2010 05:00 PM
    lantek expert, v27
    • Replies: 18
    • Views: 21,265
    08-03-2021, 01:40 PM Go to last post
  10. Need Help!- Hypertherm D80 Cant connect to host computer

    Started by Jesse_c20‎, 07-29-2021 11:18 AM
    cnc, computer, hypertherm, koike, predator editor
    • Replies: 1
    • Views: 296
    07-29-2021, 12:26 PM Go to last post
  11. Plasma Controller

    Started by BenoitMyrand‎, 01-24-2021 01:10 AM
    cnc, control, height, software, torch
    • Replies: 7
    • Views: 1,220
    07-23-2021, 09:48 PM Go to last post
  12. Need Help!- Plasma/ Router table

    Started by ECaseyP‎, 07-11-2021 10:01 PM
    build, cnc, plasma, plasma table build, table
    • Replies: 4
    • Views: 604
    07-12-2021, 08:47 PM Go to last post
  13. Need Help!- Need a recommendation on a control board for plasma cutter

    Started by tas99‎, 06-27-2021 04:50 PM
    board, control, cutter, height, recommendations
    • Replies: 3
    • Views: 649
    06-29-2021, 10:00 AM Go to last post
  14. Need Help!- My plasma torch not moving up and down..HYD-THC XPTHC-4H

    Started by dharnishpatel‎, 08-03-2018 04:13 PM
    • Replies: 5
    • Views: 2,732
    06-09-2021, 12:53 AM Go to last post
  15. Need Help!- Torch keeps going on and off repeatedly

    Started by saadsallaq‎, 06-08-2021 05:57 AM
    clicking, cutter, repeatedly, solenoid, torch
    • Replies: 0
    • Views: 278
    06-08-2021, 05:57 AM Go to last post
  16. Need Help!- SH-HC31 THC install

    Started by KPB‎, 11-13-2020 12:45 AM
    cnc, controller, plasma, table, thc
    • Replies: 3
    • Views: 957
    06-06-2021, 06:35 AM Go to last post
  17. STV SparX4800 CNC - Nevada - What a ride!

    Started by tchadwyk‎, 04-25-2021 02:52 PM
    cnc, experience, small, software, stv
    • Replies: 2
    • Views: 639
    05-23-2021, 06:40 PM Go to last post
  18. RZNC 0501 Baileigh PT 44 plasma controller issue

    Started by phaefner‎, 05-22-2021 12:53 PM
    • Replies: 0
    • Views: 298
    05-22-2021, 12:53 PM Go to last post

Page 1 of 62 12341151 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 12 users browsing this forum. (0 members & 12 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands