General CNC Plasma / Oxy Fuel Cutting Machines


Page 1 of 62 12341151 ... LastLast
Threads 1 to 20 of 1222

Forum: General CNC Plasma / Oxy Fuel Cutting Machines

CNC Plasma and Oxy Fuel Cutting Machines

  1. Need Help!- My plasma torch not moving up and down..HYD-THC XPTHC-4H

    Started by dharnishpatel‎, 08-03-2018 03:13 PM
    • Replies: 5
    • Views: 2,175
    06-08-2021, 11:53 PM Go to last post
  2. Need Help!- Torch keeps going on and off repeatedly

    Started by saadsallaq‎, 06-08-2021 04:57 AM
    clicking, cutter, repeatedly, solenoid, torch
    • Replies: 0
    • Views: 89
    06-08-2021, 04:57 AM Go to last post
  3. Need Help!- SH-HC31 THC install

    Started by KPB‎, 11-12-2020 11:45 PM
    cnc, controller, plasma, table, thc
    • Replies: 3
    • Views: 649
    06-06-2021, 05:35 AM Go to last post
  4. STV SparX4800 CNC - Nevada - What a ride!

    Started by tchadwyk‎, 04-25-2021 01:52 PM
    cnc, experience, small, software, stv
    • Replies: 2
    • Views: 419
    05-23-2021, 05:40 PM Go to last post
  5. RZNC 0501 Baileigh PT 44 plasma controller issue

    Started by phaefner‎, 05-22-2021 11:53 AM
    • Replies: 0
    • Views: 131
    05-22-2021, 11:53 AM Go to last post
  6. Post Need Help!- Adding Hypertherm THC Sensor to a Burny 3 control

    Started by MgW1‎, 05-12-2021 11:32 AM
    burny, control, hypertherm, sensor, thc
    • Replies: 0
    • Views: 241
    05-12-2021, 11:32 AM Go to last post
  7. Hypertherm 260XD won't arc on

    Started by gts16774‎, 05-02-2021 04:17 PM
    • Replies: 0
    • Views: 601
    05-02-2021, 04:17 PM Go to last post
  8. Need Help!- problem with burny phantom mnt -13720

    Started by walid2525‎, 04-19-2021 06:23 PM
    burny, cnc, idea, machine, problem
    • Replies: 1
    • Views: 249
    04-20-2021, 06:48 PM Go to last post
  9. Question What is Corner/Ext Ref?

    Started by maudib32‎, 04-20-2021 02:54 PM
    • Replies: 0
    • Views: 139
    04-20-2021, 02:54 PM Go to last post
  10. Need Help!- THC Proma 150 Problems

    Started by stevenquinn34‎, 04-18-2021 09:13 PM
    arc, lights, terminals, thc, voltage
    • Replies: 0
    • Views: 323
    04-18-2021, 09:13 PM Go to last post
  11. Need Help!- CNC STUCK IN OXYGEN FUEL AND WONT SWITCH BACK TO PLASMA.

    Started by chrisf2001‎, 04-11-2021 02:48 PM
    cnc, fuel, oxygen, plasma, stuck
    • Replies: 2
    • Views: 373
    04-12-2021, 04:35 AM Go to last post
  12. Use an older hypertherm 900 or buy new

    Started by deyzin‎, 04-12-2021 12:22 AM
    buy, cnc, duramax, machine, torch
    • Replies: 0
    • Views: 246
    04-12-2021, 12:22 AM Go to last post
  13. Shop Sabre plasma

    Started by Hexheadart‎, 03-17-2021 08:08 AM
    shop sabre plasma table
    • Replies: 1
    • Views: 1,632
    03-21-2021, 09:05 AM Go to last post
  14. Plasma controller kit

    Started by VE360‎, 03-11-2021 11:19 PM
    cnc, controller, i’m, kit, sheet
    • Replies: 2
    • Views: 479
    03-18-2021, 06:14 AM Go to last post
  15. Help!

    Started by Geosmi‎, 03-16-2021 10:37 PM
    circle, edges, george, rounded, upload
    • Replies: 1
    • Views: 309
    03-17-2021, 04:43 PM Go to last post
  16. Need Help!- Starfire program

    Started by J_perez17‎, 03-16-2021 04:17 PM
    • Replies: 0
    • Views: 300
    03-16-2021, 04:17 PM Go to last post
  17. australian plasma cnc builders i need your advice

    Started by deano_pamela‎, 03-14-2021 03:26 PM
    australia, cnc plasma
    • Replies: 0
    • Views: 236
    03-14-2021, 03:26 PM Go to last post
  18. AXBB-E Controller and Closed Loop Nema 34 Motors

    Started by GCable‎, 03-12-2021 02:54 PM
    cnc, diy, isolated ports, plasma, software
    • Replies: 2
    • Views: 353
    03-13-2021, 10:49 AM Go to last post
  19. Question Torch Height Control advice

    Started by Dogpound‎, 03-09-2021 04:42 PM
    cnc, table, thc, torch, torch height controller
    • Replies: 0
    • Views: 348
    03-09-2021, 04:42 PM Go to last post

Page 1 of 62 12341151 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 4 users browsing this forum. (1 members & 3 guests)

  1. JKMotorsports

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands