General CNC Plasma / Oxy Fuel Cutting Machines


Page 1 of 59 12341151 ... LastLast
Threads 1 to 20 of 1162

Forum: General CNC Plasma / Oxy Fuel Cutting Machines

CNC Plasma and Oxy Fuel Cutting Machines

  1. Mixing steppers and servos on same machine?

    Started by philofab‎, Yesterday 03:37 PM
    • Replies: 3
    • Views: 65
    Today, 01:22 AM Go to last post
    • Replies: 0
    • Views: 90
    08-06-2020, 01:30 AM Go to last post
  2. Help with THC wired and setup

    Started by gamaz7‎, 01-04-2019 07:48 PM
    cnc, connect, plasma, thc, working
    • Replies: 1
    • Views: 656
    08-05-2020, 10:41 PM Go to last post
  3. Build Thread- Review - My Arclight ArcrPro 12000 CNC Plasma

    Started by BarnFab‎, 10-02-2012 07:37 PM
    2 Pages
    1 2
    almost, asking, far, goes, hypertherm powermax 85, its, look, mos, next, powermax 85, then
    • Replies: 23
    • Views: 15,201
    08-04-2020, 02:28 PM Go to last post
  4. Question DIY torch height control

    Started by mjp‎, 11-19-2007 10:27 PM
    2 Pages
    1 2
    • Replies: 37
    • Views: 73,807
    07-30-2020, 08:16 AM Go to last post
  5. Burny 3 controller problems..Help!

    Started by Welderpaul‎, 06-08-2012 05:17 PM
    its, newish, saw, then
    • Replies: 14
    • Views: 9,427
    07-25-2020, 10:34 AM Go to last post
  6. Burny 3 CNC Path Error

    Started by East123‎, 07-25-2020 10:33 AM
    burny3 cnc
    • Replies: 0
    • Views: 84
    07-25-2020, 10:33 AM Go to last post
  7. Lantek

    Started by scott24‎, 04-05-2011 03:09 AM
    onto, say, then
    • Replies: 9
    • Views: 8,306
    07-22-2020, 01:55 AM Go to last post
  8. Esab ultrarex with nce 290, 320 ,520 stering

    Started by Bad_boym‎, 01-18-2020 02:16 PM
    • Replies: 12
    • Views: 385
    07-21-2020, 10:25 AM Go to last post
    • Replies: 2
    • Views: 353
    07-19-2020, 11:05 AM Go to last post
  9. Esab nce 290 floppy boot problem

    Started by ray6171‎, 07-17-2020 09:06 AM
    boot floppy esab nce
    • Replies: 0
    • Views: 113
    07-17-2020, 09:06 AM Go to last post
  10. Esab controller NCE 390

    Started by Dem1‎, 09-08-2019 07:37 AM
    drives, esab, floppy, nce, running
    • Replies: 6
    • Views: 801
    07-17-2020, 07:30 AM Go to last post
  11. Need Help!- Upgrade

    Started by pjsbird‎, 07-13-2020 12:58 PM
    blaze, plasmaroute, table, upgrade
    • Replies: 0
    • Views: 144
    07-13-2020, 12:58 PM Go to last post
  12. Pronest Post Processor CFF File

    Started by cah‎, 07-13-2020 11:50 AM
    cff, file, post, processor, pronest
    • Replies: 0
    • Views: 283
    07-13-2020, 11:50 AM Go to last post
  13. Need Help!- Plasma torch stops before cut is ready

    Started by d3workz‎, 07-10-2020 04:17 PM
    cnc, command, cut, ready, wrong
    • Replies: 0
    • Views: 118
    07-10-2020, 04:17 PM Go to last post
  14. Replace cebora torch with hypertherm

    Started by gyvara_gy‎, 07-07-2020 10:50 AM
    cebora, replacement, torch
    • Replies: 0
    • Views: 115
    07-07-2020, 10:50 AM Go to last post
    • Replies: 0
    • Views: 129
    07-07-2020, 06:52 AM Go to last post
  15. Need Help!- ESAB Ultrarex UXD-P2500 alternative software

    Started by hayaome‎, 05-27-2014 03:25 AM
    maybe
    • Replies: 7
    • Views: 2,147
    07-03-2020, 11:39 AM Go to last post
  16. plasma z axis and proma 150 thc, linit switches

    Started by adricar144‎, 06-26-2020 01:25 PM
    cnc, limit switch, proma150, thc, z axis
    • Replies: 1
    • Views: 174
    06-27-2020, 04:58 AM Go to last post
  17. Need Help!- Torch Height Issue

    Started by halelesk‎, 06-19-2020 07:23 PM
    cnc, floating, issue, plasma cnc, torch
    • Replies: 0
    • Views: 208
    06-19-2020, 07:23 PM Go to last post

Page 1 of 59 12341151 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 15 users browsing this forum. (1 members & 14 guests)

  1. NIC 77

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands