Reply with QuoteContact the card manufacturer and ask if there plugin supports slaved homing.
MKX-4 Mach3 don't work slave axis home
Card MKX-IV. If the axis A configured slave from the Yaxes, when pressed “Ref all Home” Mach3 does not respond to the switch Ahome only switch the main axis. Don't work A axis home.
Mach3Mill.xml: https://yadi.sk/d/48R5yb4YtrH2n
Similar Threads:
Re: MKX-4 Mach3 don't work slave axis home
Contact the card manufacturer and ask if there plugin supports slaved homing.
Gerry
UCCNC 2017 Screenset
[URL]http://www.thecncwoodworker.com/2017.html[/URL]
Mach3 2010 Screenset
[URL]http://www.thecncwoodworker.com/2010.html[/URL]
JointCAM - CNC Dovetails & Box Joints
[URL]http://www.g-forcecnc.com/jointcam.html[/URL]
(Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
Re: MKX-4 Mach3 don't work slave axis home
The manufacturer not answer.Originally Posted by ger21
A similar problem on two cards purchased in different places.
Slave A_axis stops along with Y_axis (switch YHome).
It is imposible to correct skew of the axis(((
Re: MKX-4 Mach3 don't work slave axis home
Make sure that "Home Slave with Master" in General Config is NOT checked.
Gerry
UCCNC 2017 Screenset
[URL]http://www.thecncwoodworker.com/2017.html[/URL]
Mach3 2010 Screenset
[URL]http://www.thecncwoodworker.com/2010.html[/URL]
JointCAM - CNC Dovetails & Box Joints
[URL]http://www.g-forcecnc.com/jointcam.html[/URL]
(Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
Re: MKX-4 Mach3 don't work slave axis home
Thanks for your answer.
Yes: "General Config"->"Home Slave with Master" is not checked.
If A_axes is not slave, all 4 home swiches works good.
Re: MKX-4 Mach3 don't work slave axis home
Sounds like the plugin does not support slaved homing.
Gerry
UCCNC 2017 Screenset
[URL]http://www.thecncwoodworker.com/2017.html[/URL]
Mach3 2010 Screenset
[URL]http://www.thecncwoodworker.com/2010.html[/URL]
JointCAM - CNC Dovetails & Box Joints
[URL]http://www.g-forcecnc.com/jointcam.html[/URL]
(Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
Re: MKX-4 Mach3 don't work slave axis home
You are right, the plugin works incorrectly. View time when triggered "A Pos" led'
Re: MKX-4 Mach3 don't work slave axis home
Hello
I have the same card mkx-IV driver v2.39.9 and mach3.
Have you been able to solve your problem?
I have a switch on each motor of my axis (Y & A).
Axis A is slave to the Y axis.
When I run a RefHome RefHome (2),
1- Y and A move together until touching switch Y.
2- Y and A stop
3- Nothing happens but I have to trigger switch A by hand.
4- Y and A go back.
If I resume the step by first releasing the switch A
1- Y and A move together until touching switch A.
2- Y and A do not stop
3- I trigger the Y switch by hand.
4- Y and A stop
5- Y and A go back.
An idea of ??why this behavior?
MyShop
