StepperCalc unipolar resistor calculator


Results 1 to 15 of 15

Thread: StepperCalc unipolar resistor calculator

  1. #1
    Registered balsaman's Avatar
    Join Date
    Mar 2003
    Location
    Canada
    Posts
    2139
    Downloads
    0
    Uploads
    0

    Default StepperCalc unipolar resistor calculator

    For anyone interested, I have writen a program to help you select current limiting resistors for your unipolar steppermotors.

    I know it can be calculated easily with ohm's law but this is easier and great for newbies.

    It also calculates powersupply minimum current rating based on the motor current and the number of motors used.

    The best way to use it is to enter your motor and powersupply data, then hit calculate. Since resistors don't come in values to 2 decimal places, you can then select "I want to calculate motor current" and enter the closest available resistor size to calculate actual motor current based on the resistor you choose.

    You can select transistor or FET outputs on your controller, and whether you want 2 resistors per motor or one with the center taps tied together.

    Download it here: www.e-zflight.com/files/stepcalc102.zip

    Let me know if you download it, and how you like it.

    Here is the screen shot.

    Eric

    Similar Threads:
    Attached Thumbnails Attached Thumbnails StepperCalc unipolar resistor calculator-cnczzg-jpg  
    I wish it wouldn't crash.


  2. #2

    Default

    I cannot download the file. Can anyone send this file to me at nusar@juno.com ?

    Steve



  3. #3
    Moderator wms's Avatar
    Join Date
    Mar 2003
    Location
    United States
    Posts
    923
    Downloads
    0
    Uploads
    0

    Default

    Here it comes!

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  4. #4
    Registered balsaman's Avatar
    Join Date
    Mar 2003
    Location
    Canada
    Posts
    2139
    Downloads
    0
    Uploads
    0

    Default

    Works for me...try right click and choose "Save File As"

    Eric

    I wish it wouldn't crash.


  5. #5
    Registered
    Join Date
    Mar 2005
    Location
    Romania
    Posts
    339
    Downloads
    8
    Uploads
    0

    Default

    Hi,

    Can somebody help me and put the calculator here for downloading? I need to calculate the limiting resistors and it seems that the web domain/page was sold and the file disappeared. Thank you.



  6. #6
    Registered
    Join Date
    Dec 2004
    Location
    Barbados
    Posts
    1316
    Downloads
    0
    Uploads
    0

    Default

    Hi Zoltan,

    Try the link below. It seems to be a different program to the one balsaman wrote.

    http://www.eftechusa.com/downloads.htm


    Jason



  7. #7
    Registered
    Join Date
    Mar 2005
    Location
    Romania
    Posts
    339
    Downloads
    8
    Uploads
    0

    Default

    Hi,

    Thank you very much.



  8. #8
    Registered
    Join Date
    Jun 2005
    Location
    USA
    Posts
    55
    Downloads
    0
    Uploads
    0

    Default

    Sorry to drag up this old post, but I'm new and want to do the right thing without burning my electronics up. I have 3 Astrosyn, 23LM-C708-P1, unipolar, eight wire stepper motors. I'm using the FET-3 board and purchased it with the 24V, 3A power supply and 3 Step-Syn, 103-771-18, unipolar, 5 wire, stepper motors. The Astrosyn motors are rated at 3.6V/phase and 2.4A/phase. The Step-Syn motors are rated at 24V and 0.18A. Using StepperCalc, If I put 24V as my power supply voltage, 2.4 as the Motor Current (Amps) and 3.6 as the Motor Voltage (Volts); I get 8.50 ohms as the resistor value, 48.96 watts as the minimum resistor wattage and 14.40 amps as the power supply minimum current rating. Now that I've gotten that out of the way I can finally ask some questions:
    1. What are the specs on an actual resistor that will meet my needs?
    2. Where can I buy them?
    3. Since I have to bring all my center taps together to use the eight wire like a five wire stepper, can I use just one resistor? (I did the Stepper Calc formula using one resistor)
    4. Can I keep the two coils seperated and have two center taps and wire it like a six wire stepper?
    5. Is there any advantage to doing that?
    6. Where can I get a 24 Volt, 14.40 Amp power supply? (It would be nice if it had a 5V, 1.5A tap to power my controller board.)
    7. Since the FET-3 board can take 35V continuous and 50V start up, do you think it would hurt it to run at 36V.
    8. How much difference in torque will I get if I go to 36V? (Don't need an exact number, just need to know if it's worth the risk)
    9. How crappy would these motors run at 3.6V so I wouldn't need resistors at all?

    Thanks for any light anyone can shed on my questions. I can't wait to get this thing running! Great site and I will be donating as soon as my router is cutting. (just in case I have to spend my last $60 on Ebay to finish it)

    Randall



  9. #9
    Community Moderator ger21's Avatar
    Join Date
    Mar 2003
    Location
    Shelby Township
    Posts
    35138
    Downloads
    1
    Uploads
    0

    Default

    I'll answer a few

    3) see 4
    4) this is the way they should be wired. You'll need 2 resistors per motor.
    6) Ebay - http://cgi.ebay.com/ws/eBayISAPI.dll...Name=WDVW&rd=1
    7) It might be OK, but will probably run hotter. You'll need even bigger resistors, though, right?
    8) low speed torque will remain the same. useable high speed rpm will increase, proportional to voltage. 50% more voltage should get you about %50 more speed.
    9) They turn, but probably not much more.

    Gerry

    UCCNC 2017 Screenset
    http://www.thecncwoodworker.com/2017.html

    Mach3 2010 Screenset
    http://www.thecncwoodworker.com/2010.html

    JointCAM - CNC Dovetails & Box Joints
    http://www.g-forcecnc.com/jointcam.html

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  10. #10
    Registered
    Join Date
    Jun 2005
    Location
    USA
    Posts
    55
    Downloads
    0
    Uploads
    0

    Default

    Thanks for the quick answers Ger. Do you know how much that power supply is worth? Any chance you know the answer to number 5? I realize I will have to get bigger resistors if I increase Voltage.
    Thanks again,
    Randall



  11. #11
    Community Moderator ger21's Avatar
    Join Date
    Mar 2003
    Location
    Shelby Township
    Posts
    35138
    Downloads
    1
    Uploads
    0

    Default

    Quote Originally Posted by Xterrian
    Any chance you know the answer to number 5?
    I don't think that #3 is the correct way to wire it, which makes #5 irrelevant, imo. I could be wrong, though, but everything I've read says an 8 wire motor is wired like a 6 wire for unipolar drives.

    Gerry

    UCCNC 2017 Screenset
    http://www.thecncwoodworker.com/2017.html

    Mach3 2010 Screenset
    http://www.thecncwoodworker.com/2010.html

    JointCAM - CNC Dovetails & Box Joints
    http://www.g-forcecnc.com/jointcam.html

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  12. #12
    Registered
    Join Date
    Jun 2005
    Location
    USA
    Posts
    55
    Downloads
    0
    Uploads
    0

    Default

    I'll probably try it both ways. If I do the 6 wire method I can use smaller resistors and get them from stepperworld, so that's a plus. I just want to be sure I won't burn anything up. Any idea what those power supplies cost new?



  13. #13
    Community Moderator ger21's Avatar
    Join Date
    Mar 2003
    Location
    Shelby Township
    Posts
    35138
    Downloads
    1
    Uploads
    0

    Default

    Quote Originally Posted by Xterrian
    . Any idea what those power supplies cost new?
    Probably around $200 or more.

    Here's another source. http://www.mpja.com/listitems.asp?dept=3&main=1

    Gerry

    UCCNC 2017 Screenset
    http://www.thecncwoodworker.com/2017.html

    Mach3 2010 Screenset
    http://www.thecncwoodworker.com/2010.html

    JointCAM - CNC Dovetails & Box Joints
    http://www.g-forcecnc.com/jointcam.html

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  14. #14
    Registered
    Join Date
    Jun 2005
    Location
    USA
    Posts
    55
    Downloads
    0
    Uploads
    0

    Default

    Thanks for all the answers! I love this place. I hate the sleep deprivation it causes though.

    Randall



  15. #15
    Registered
    Join Date
    Jan 2009
    Location
    usa
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default





Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

StepperCalc unipolar resistor calculator

StepperCalc unipolar resistor calculator

StepperCalc unipolar resistor calculator