Gecko Drives


Page 1 of 106 12341151101 ... LastLast
Threads 1 to 20 of 2101

Forum: Gecko Drives

Discuss all Gecko drives here and get direct support!

Sub-Forums Threads / Posts  Last Post

  1. Discuss G-REX here.

    Forum Actions:

    Forum Statistics:

    • Threads: 48
    • Posts: 356
  1. Sticky Threads
  2. Sticky Thread Sticky: Geckodrive FAQ: General, Steppers, and Servo Questions Answered

    Started by CoAMarcus‎, 02-07-2008 09:04 PM
    000rpm, 213, 65%, almost, another, away, current draw, down, except, four, goes, indicate, keep, machinis, motor wiring, next, not, rps, say, since, then, useful, whatever
    • Replies: 0
    • Views: 50,923
    02-07-2008, 09:04 PM Go to last post
  3. Forum Threads
    • Replies: 6
    • Views: 635
    09-17-2020, 04:08 PM Go to last post
  1. G540 Failing...not faulting

    Started by Catmandu13‎, 08-03-2020 12:17 AM
    48v, cnc, continuity, estop, g540
    • Replies: 1
    • Views: 427
    08-19-2020, 09:55 AM Go to last post
  2. New Machine Build- Enclosure Fan

    Started by john1285‎, 08-17-2020 05:50 PM
    blow, box, case, fan, g540
    • Replies: 1
    • Views: 270
    08-18-2020, 03:25 AM Go to last post
  3. G540 Motherboard Rev4

    Started by spidey4fun‎, 08-06-2020 10:12 AM
    g540, local, motherboard, parts, rev4
    • Replies: 1
    • Views: 421
    08-17-2020, 10:57 PM Go to last post
  4. Mach3 is moving too far like scale is off

    Started by MP40cal‎, 08-15-2020 07:24 PM
    mach2/3, machine, move, moving, processor
    • Replies: 0
    • Views: 300
    08-15-2020, 07:24 PM Go to last post
  5. Need Help!- G320 Brush Servo Drive errors on K2 2525

    Started by Robot Dude‎, 09-22-2016 02:11 PM
    • Replies: 7
    • Views: 1,171
    08-08-2020, 01:34 PM Go to last post
  6. Gecko G540 and Mach3 XML PLEASE HELP ME

    Started by MP40cal‎, 08-01-2020 05:04 PM
    cut, file, g540, inches, mach3
    • Replies: 6
    • Views: 547
    08-02-2020, 09:47 PM Go to last post
  7. new G540 FAULT LED LIT

    Started by Mr.Chips‎, 07-18-2020 02:17 PM
    fault, lit, pin, position, switch
    • Replies: 0
    • Views: 309
    07-18-2020, 02:17 PM Go to last post
  8. Need Help!- Fanuc Yellow Cap to Gecko 320X

    Started by Floriptoolworks‎, 02-11-2019 02:28 PM
    drive, fine, machine, running, started
    • Replies: 2
    • Views: 484
    07-15-2020, 09:44 PM Go to last post
  9. Resistor for unknown nema 23

    Started by cncneon‎, 07-10-2020 06:27 PM
    hot, letting, nema, resistor, unknown
    • Replies: 3
    • Views: 375
    07-12-2020, 05:51 PM Go to last post
  10. G540 and Mach3 Random EStops Fixed For Me

    Started by smapdiage9‎, 05-26-2020 12:57 AM
    estop, mach3, pin, problem, switch
    • Replies: 1
    • Views: 455
    07-05-2020, 10:26 AM Go to last post
  11. G320 starts immediately on power-up

    Started by MattTheNoob‎, 06-27-2020 03:51 PM
    disconnected, g320, immediately, machine, starts
    • Replies: 1
    • Views: 297
    06-27-2020, 06:39 PM Go to last post
  12. G340 issue

    Started by xumexuha‎, 06-17-2020 02:21 AM
    • Replies: 0
    • Views: 232
    06-17-2020, 02:21 AM Go to last post
  13. acorn and G540 limit switches

    Started by BentWerx‎, 06-15-2020 09:34 PM
    acorn, correct, g540, limit, switches
    • Replies: 0
    • Views: 299
    06-15-2020, 09:34 PM Go to last post
  14. Gecko G201x power on problem

    Started by Onha‎, 05-27-2020 04:27 PM
    • Replies: 0
    • Views: 288
    05-27-2020, 04:27 PM Go to last post
  15. Problems on installing rotary encoder on Gecko G540

    Started by Rimbaldo‎, 05-23-2020 06:41 PM
    • Replies: 8
    • Views: 436
    05-24-2020, 11:56 AM Go to last post
  16. Need Help!- Gecko 540 controller and VFD

    Started by MatthewBasaraba‎, 05-23-2020 01:39 PM
    • Replies: 4
    • Views: 373
    05-23-2020, 03:20 PM Go to last post
  17. Damaged G540

    Started by Happy Feet‎, 05-22-2020 08:57 AM
    • Replies: 0
    • Views: 250
    05-22-2020, 08:57 AM Go to last post

Page 1 of 106 12341151101 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 5 users browsing this forum. (0 members & 5 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands