Gecko Drives


Page 1 of 106 12341151101 ... LastLast
Threads 1 to 20 of 2105

Forum: Gecko Drives

Discuss all Gecko drives here and get direct support!

Sub-Forums Threads / Posts  Last Post

  1. Discuss G-REX here.

    Forum Actions:

    Forum Statistics:

    • Threads: 48
    • Posts: 356
  1. Sticky Threads
  2. Sticky Thread Sticky: Geckodrive FAQ: General, Steppers, and Servo Questions Answered

    Started by CoAMarcus‎, 02-07-2008 09:04 PM
    000rpm, 213, 65%, almost, another, away, current draw, down, except, four, goes, indicate, keep, machinis, motor wiring, next, not, rps, say, since, then, useful, whatever
    • Replies: 0
    • Views: 51,508
    02-07-2008, 09:04 PM Go to last post
  3. Forum Threads
    • Replies: 0
    • Views: 173
    01-11-2021, 01:02 PM Go to last post
    • Replies: 2
    • Views: 423
    01-03-2021, 12:25 AM Go to last post
  1. Moved: Newbie- Spidercam

    Started by Helivideo‎, 12-20-2020 12:18 PM
    •  
    •  
  2. Need Help!- Geckodrive g320x error/reset terminal 5 ?

    Started by kansaswoodrat‎, 12-06-2020 03:18 PM
    cabinet, current, forum, small, terminal
    • Replies: 0
    • Views: 337
    12-06-2020, 03:18 PM Go to last post
    • Replies: 6
    • Views: 781
    09-17-2020, 04:08 PM Go to last post
  3. G540 Failing...not faulting

    Started by Catmandu13‎, 08-03-2020 12:17 AM
    48v, cnc, continuity, estop, g540
    • Replies: 1
    • Views: 522
    08-19-2020, 09:55 AM Go to last post
  4. New Machine Build- Enclosure Fan

    Started by john1285‎, 08-17-2020 05:50 PM
    blow, box, case, fan, g540
    • Replies: 1
    • Views: 382
    08-18-2020, 03:25 AM Go to last post
  5. G540 Motherboard Rev4

    Started by spidey4fun‎, 08-06-2020 10:12 AM
    g540, local, motherboard, parts, rev4
    • Replies: 1
    • Views: 558
    08-17-2020, 10:57 PM Go to last post
  6. Mach3 is moving too far like scale is off

    Started by MP40cal‎, 08-15-2020 07:24 PM
    mach2/3, machine, move, moving, processor
    • Replies: 0
    • Views: 421
    08-15-2020, 07:24 PM Go to last post
  7. Need Help!- G320 Brush Servo Drive errors on K2 2525

    Started by Robot Dude‎, 09-22-2016 02:11 PM
    • Replies: 7
    • Views: 1,277
    08-08-2020, 01:34 PM Go to last post
  8. Gecko G540 and Mach3 XML PLEASE HELP ME

    Started by MP40cal‎, 08-01-2020 05:04 PM
    cut, file, g540, inches, mach3
    • Replies: 6
    • Views: 669
    08-02-2020, 09:47 PM Go to last post
  9. new G540 FAULT LED LIT

    Started by Mr.Chips‎, 07-18-2020 02:17 PM
    fault, lit, pin, position, switch
    • Replies: 0
    • Views: 367
    07-18-2020, 02:17 PM Go to last post
  10. Need Help!- Fanuc Yellow Cap to Gecko 320X

    Started by Floriptoolworks‎, 02-11-2019 02:28 PM
    drive, fine, machine, running, started
    • Replies: 2
    • Views: 541
    07-15-2020, 09:44 PM Go to last post
  11. Resistor for unknown nema 23

    Started by cncneon‎, 07-10-2020 06:27 PM
    hot, letting, nema, resistor, unknown
    • Replies: 3
    • Views: 445
    07-12-2020, 05:51 PM Go to last post
  12. G540 and Mach3 Random EStops Fixed For Me

    Started by smapdiage9‎, 05-26-2020 12:57 AM
    estop, mach3, pin, problem, switch
    • Replies: 1
    • Views: 515
    07-05-2020, 10:26 AM Go to last post
  13. G320 starts immediately on power-up

    Started by MattTheNoob‎, 06-27-2020 03:51 PM
    disconnected, g320, immediately, machine, starts
    • Replies: 1
    • Views: 351
    06-27-2020, 06:39 PM Go to last post
  14. G340 issue

    Started by xumexuha‎, 06-17-2020 02:21 AM
    • Replies: 0
    • Views: 270
    06-17-2020, 02:21 AM Go to last post
  15. acorn and G540 limit switches

    Started by BentWerx‎, 06-15-2020 09:34 PM
    acorn, correct, g540, limit, switches
    • Replies: 0
    • Views: 353
    06-15-2020, 09:34 PM Go to last post

Page 1 of 106 12341151101 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 8 users browsing this forum. (0 members & 8 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands