ATC. Automatic Tool Changer issue. Leadwell Mill, MCV-OP Fanuc OM controller


Page 1 of 2 12 LastLast
Results 1 to 20 of 36

Thread: ATC. Automatic Tool Changer issue. Leadwell Mill, MCV-OP Fanuc OM controller

  1. #1
    Member
    Join Date
    Mar 2011
    Location
    Australia
    Posts
    182
    Downloads
    0
    Uploads
    0

    Default ATC. Automatic Tool Changer issue. Leadwell Mill, MCV-OP Fanuc OM controller

    Hi guys, I'm starting another thread on the issue of ATC not working.
    A bit of history, the parameters were deleted, i think from the machine being powerless for 3 years??
    Anyhow I have put the parameters back in from an old floppy disk and from my service book.
    The Mill is slowly coming back to life as i can now load programs but cannot change tools even in MDI. The changer basically turns back and forth, it doesn't actuate down and across. (Not an arm type tool changer)
    zavateandu was greatly helping me out a few months ago but i think the issue was because the technician had my service book (4 or 5 months of calling him) which I had to go to and check some parameters and ladders. The ladders is something i have very little clue about other than i think its a series of switches??
    Thanks guys
    Bart



    Similar Threads:


  2. #2

    Default Re: ATC. Automatic Tool Changer issue. Leadwell Mill, MCV-OP Fanuc OM controller

    Are there any PC parameter settings in your manual? On that series they would be Diagnostics in the 300's.
    Looks like a counter or timer is possibly not set. Its also possible that a value in the Diagnostics was set base on the location of the Magazine at that time and is now causing a conflict based on its current location.



  3. #3
    Member
    Join Date
    Mar 2011
    Location
    Australia
    Posts
    182
    Downloads
    0
    Uploads
    0

    Default Re: ATC. Automatic Tool Changer issue. Leadwell Mill, MCV-OP Fanuc OM controller

    thank you.
    ill have to scan some parameters and probably ladders?
    I remember now, its been a few months but i was supposed to share this with zavateandu but i didn't have the manual. I have the manual now so ill scan it.




  4. #4
    Member
    Join Date
    Mar 2011
    Location
    Australia
    Posts
    182
    Downloads
    0
    Uploads
    0

    Default Re: ATC. Automatic Tool Changer issue. Leadwell Mill, MCV-OP Fanuc OM controller

    Parameters

    Last edited by toranacar; 07-05-2022 at 05:55 AM.


  5. #5
    Member
    Join Date
    Mar 2011
    Location
    Australia
    Posts
    182
    Downloads
    0
    Uploads
    0

    Default Re: ATC. Automatic Tool Changer issue. Leadwell Mill, MCV-OP Fanuc OM controller

    Parameters
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0016-jpg
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0015-jpg
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0014-jpg
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0013-jpg
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0012-jpg
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0011-jpg
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0010-jpg
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0009-jpg

    Last edited by toranacar; 07-05-2022 at 06:38 AM.


  6. #6
    Member
    Join Date
    Mar 2011
    Location
    Australia
    Posts
    182
    Downloads
    0
    Uploads
    0

    Default Re: ATC. Automatic Tool Changer issue. Leadwell Mill, MCV-OP Fanuc OM controller

    Parameters
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0024-jpg
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0023-jpg
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0022-jpg
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0021-jpg
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0020-jpg
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0019-jpg
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0018-jpg
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0017-jpg

    Last edited by toranacar; 07-05-2022 at 06:35 AM.


  7. #7
    Member
    Join Date
    Mar 2011
    Location
    Australia
    Posts
    182
    Downloads
    0
    Uploads
    0

    Default Re: ATC. Automatic Tool Changer issue. Leadwell Mill, MCV-OP Fanuc OM controller

    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0008-jpg
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0007-jpg
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0006-jpg
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0005-jpg
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0004-jpg
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0004-jpg
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0002-jpg
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-img_20220705_0001-jpg



  8. #8
    Member machinehop5's Avatar
    Join Date
    Aug 2009
    Location
    United States
    Posts
    1279
    Downloads
    5
    Uploads
    2

    Default Re: ATC. Automatic Tool Changer issue. Leadwell Mill, MCV-OP Fanuc OM controller

    ...just a quick reminder about changing Parameters....you must cycle the Control OFF, then back ON to take affect.



  9. #9
    Member
    Join Date
    Mar 2011
    Location
    Australia
    Posts
    182
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by machinehop5 View Post
    ...just a quick reminder about changing Parameters....you must cycle the Control OFF, then back ON to take affect.
    That's a great point. I discovered that with the download issue a few days ago.



  10. #10
    Member
    Join Date
    Mar 2011
    Location
    Australia
    Posts
    182
    Downloads
    0
    Uploads
    0

    Default Re: ATC. Automatic Tool Changer issue. Leadwell Mill, MCV-OP Fanuc OM controller

    2 or 3 of the ladder diagrams show the ATC



  11. #11
    Member machinehop5's Avatar
    Join Date
    Aug 2009
    Location
    United States
    Posts
    1279
    Downloads
    5
    Uploads
    2

    Default Re: ATC. Automatic Tool Changer issue. Leadwell Mill, MCV-OP Fanuc OM controller

    Quote Originally Posted by toranacar View Post
    2 or 3 of the ladder diagrams show the ATC
    ...yes, its great you have most if, not all the paperwork with machine. Which makes me wonder what else is on the Floppies you have. Also, does your machine have a Hard Drive? Is there more than one Directory of files...what are the File or Directory names ?



  12. #12
    Member
    Join Date
    Mar 2011
    Location
    Australia
    Posts
    182
    Downloads
    0
    Uploads
    0

    Default Re: ATC. Automatic Tool Changer issue. Leadwell Mill, MCV-OP Fanuc OM controller

    I have more ladder diagrams diagrams. Ill copy more of it.
    Ill have another look at the floppy.



  13. #13
    Registered
    Join Date
    Jun 2012
    Location
    United States
    Posts
    7
    Downloads
    0
    Uploads
    0

    Default Re: ATC. Automatic Tool Changer issue. Leadwell Mill, MCV-OP Fanuc OM controller

    Anyone knows how to disable atc to put my komo machine working tool manually? Which parameter can bypass it and eliminate the alarm of tool changer not ready?



  14. #14
    Member
    Join Date
    Mar 2011
    Location
    Australia
    Posts
    182
    Downloads
    0
    Uploads
    0

    Default Re: ATC. Automatic Tool Changer issue. Leadwell Mill, MCV-OP Fanuc OM controller

    That's a good question, i want to know how to enable it



  15. #15
    Member machinehop5's Avatar
    Join Date
    Aug 2009
    Location
    United States
    Posts
    1279
    Downloads
    5
    Uploads
    2

    Default Re: ATC. Automatic Tool Changer issue. Leadwell Mill, MCV-OP Fanuc OM controller

    ...have you tried Punching the PMC Params from CNC to PC to see if there is anything in there? it might look like random numbers and letters when viewed has a TXT file.
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-fanuc0m-pmc-transfer-jpg



  16. #16
    Member
    Join Date
    Mar 2011
    Location
    Australia
    Posts
    182
    Downloads
    0
    Uploads
    0

    Default Re: ATC. Automatic Tool Changer issue. Leadwell Mill, MCV-OP Fanuc OM controller

    Quote Originally Posted by machinehop5 View Post
    ...have you tried Punching the PMC Params from CNC to PC to see if there is anything in there? it might look like random numbers and letters when viewed has a TXT file.
    ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller-fanuc0m-pmc-transfer-jpg
    No i haven't. Ill have to try that



  17. #17
    Member machinehop5's Avatar
    Join Date
    Aug 2009
    Location
    United States
    Posts
    1279
    Downloads
    5
    Uploads
    2

    Default Re: ATC. Automatic Tool Changer issue. Leadwell Mill, MCV-OP Fanuc OM controller

    ...8 bit names for files when saving to dos in 1980-90's right?



  18. #18
    Member
    Join Date
    Mar 2011
    Location
    Australia
    Posts
    182
    Downloads
    0
    Uploads
    0

    Default Re: ATC. Automatic Tool Changer issue. Leadwell Mill, MCV-OP Fanuc OM controller

    Quote Originally Posted by machinehop5 View Post
    ...8 bit names for files when saving to dos in 1980-90's right?
    I have windows XP, i think it has DOS, im pretty sure



  19. #19
    Member machinehop5's Avatar
    Join Date
    Aug 2009
    Location
    United States
    Posts
    1279
    Downloads
    5
    Uploads
    2

    Default Re: ATC. Automatic Tool Changer issue. Leadwell Mill, MCV-OP Fanuc OM controller

    ... more things to find out better late than never and confess ya--- XP time wrap
    130 Keyboard Shortcuts for Windows XP



  20. #20
    Member
    Join Date
    Mar 2011
    Location
    Australia
    Posts
    182
    Downloads
    0
    Uploads
    0

    Default Re: ATC. Automatic Tool Changer issue. Leadwell Mill, MCV-OP Fanuc OM controller

    Quote Originally Posted by machinehop5 View Post
    ... more things to find out better late than never and confess ya--- XP time wrap
    130 Keyboard Shortcuts for Windows XP




Page 1 of 2 12 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller

ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller

ATC. Automatic Tool Changer issue.  Leadwell Mill, MCV-OP Fanuc OM controller