Need Help! Fanuc Beta driver alarm L


Results 1 to 5 of 5

Thread: Fanuc Beta driver alarm L

  1. #1
    Member HonHon's Avatar
    Join Date
    Aug 2020
    Posts
    7
    Downloads
    0
    Uploads
    0

    Exclamation Fanuc Beta driver alarm L

    Hi guys my new replaced beta amp (which was from an old machine) stating alarm L every 3-4 hours and the machine is shut down since no power on drivers. The problem is that when the machine was shut down while it is running, it caused z axis to drop down about 1-2 mm, which made a spot on my finish surface; And this is horrible not talking about how it would affect the electronic components.

    Do you know why does this happen. Is it because of the beta driver is faulty or it is because of the i/o module is faulty, or even the JD1A-JD1B connection wire is faulty ??

    Similar Threads:


  2. #2

    Default Re: Fanuc Beta driver alarm L

    L indicates an I/O link issue.

    It could be caused by several things.
    When the alarm occurs will it restart immediately or does it take several restart attempts?
    Check the link LED on all components in the chain. The 1st unit in the chain that does not have the Link LED on could be at fault.
    Once it is determined which unit may be the issue check all connections to that unit are secure (24vdc supply, Link cables).
    Check the 24vdc and make sure it is not low. If you have one apply a voltage meter with record feature and watch the 24vdc.
    Possibly separate the link cable from other wires to determine if noise is an issue.

    The last item and least likely could be the beta motor encoder. If the 5 volts is getting shorted in the encoder/cable it can shut down the drive causing a link alarm. So you may want to look at that cable and ensure it is not damaged or contaminated.



  3. #3
    Member
    Join Date
    Dec 2009
    Location
    ROMANIA
    Posts
    707
    Downloads
    0
    Uploads
    0

    Default Re: Fanuc Beta driver alarm L

    the beta drives has the parameters inside it,not on the cnc so when replacing a beta drive you must upload the parameters related to the motor to the drive.
    Taking another drive from another machine will not be with the exactly the same parameters.
    if you do not have the original parameters from the old drive that is dead i supposed,you have to put the standard parameters for that motor you have connected to it



  4. #4
    Member HonHon's Avatar
    Join Date
    Aug 2020
    Posts
    7
    Downloads
    0
    Uploads
    0

    Default Re: Fanuc Beta driver alarm L

    Quote Originally Posted by zavateandu View Post
    the beta drives has the parameters inside it,not on the cnc so when replacing a beta drive you must upload the parameters related to the motor to the drive.
    Taking another drive from another machine will not be with the exactly the same parameters.
    if you do not have the original parameters from the old drive that is dead i supposed,you have to put the standard parameters for that motor you have connected to it
    Hi thank for your help zavateandu,
    I have already load the parameter from the old amp, and things was good until now except the L error sometimes show up !. But I don't understand why does the alarm has somethings to do with parameters



  5. #5
    Member
    Join Date
    Dec 2009
    Location
    ROMANIA
    Posts
    707
    Downloads
    0
    Uploads
    0

    Default Re: Fanuc Beta driver alarm L

    Like the other guy said ,the roblem is on the I/O LINK line.A servo amplifier unit connected to the line was turned off.You need to check what other components connected to it has turned off.



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Fanuc Beta driver alarm L

Fanuc Beta driver alarm L

Fanuc Beta driver alarm L