Need Help! COLCHESTER TORNADO 80 alarm 1007


Results 1 to 5 of 5

Thread: COLCHESTER TORNADO 80 alarm 1007

  1. #1
    Member petkovm's Avatar
    Join Date
    Jan 2020
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default COLCHESTER TORNADO 80 alarm 1007

    Hello!

    We have COLCHESTER TORNADO 80 with GE-FANUC 21-t
    At each attempt to rotate the spindle gives an alarm 1007 monitoring hardware fault.
    We read about the recovery procedure, but we do not have such a supplementary board.
    We will be grateful if anyone can help.

    Thanks!

    Similar Threads:


  2. #2
    Member AndyM23's Avatar
    Join Date
    Mar 2020
    Posts
    2
    Downloads
    0
    Uploads
    0

    Default Re: COLCHESTER TORNADO 80 alarm 1007

    Hi, If your tornado is equipped in SSM Board, you need to use procedure as bellow

    If, with the link, LK2, in the right hand position, +5A, the push button on the SSM is held down while the main isolator is switched on as described above to delete the Alarm History, but then is
    held longer, the SSM display cycles around the available maximum spindle speed settings
    When the required maximum speed is displayed releasing the push button writes this value to the SSM memory.
    The main isolator must now be switched off and the link restored to its normal position

    Good Luck
    In case SSM failure I can offer to repair it.



  3. #3
    Member Abashraf9803's Avatar
    Join Date
    Jan 2021
    Posts
    2
    Downloads
    0
    Uploads
    0

    Exclamation Re: COLCHESTER TORNADO 80 alarm 1007

    Quote Originally Posted by AndyM23 View Post
    Hi, If your tornado is equipped in SSM Board, you need to use procedure as bellow

    If, with the link, LK2, in the right hand position, +5A, the push button on the SSM is held down while the main isolator is switched on as described above to delete the Alarm History, but then is
    held longer, the SSM display cycles around the available maximum spindle speed settings
    When the required maximum speed is displayed releasing the push button writes this value to the SSM memory.
    The main isolator must now be switched off and the link restored to its normal position

    Good Luck
    In case SSM failure I can offer to repair it.

    Can you please specify what is the main isolator?

    I am facing a problem with my tornado 110 with fanuc 21i-t but whenever the machine boots it gives an emergency stop alarm and then 1001 spindle speed monitoring -no response



  4. #4
    Member Abashraf9803's Avatar
    Join Date
    Jan 2021
    Posts
    2
    Downloads
    0
    Uploads
    0

    Arrow Re: COLCHESTER TORNADO 80 alarm 1007

    A photo for the error ladder

    Attached Thumbnails Attached Thumbnails COLCHESTER TORNADO 80 alarm 1007-e14e8dcd-c2e1-4219-9e47-966842557dde-jpg  


  5. #5
    Member
    Join Date
    May 2016
    Location
    United Kingdom
    Posts
    503
    Downloads
    0
    Uploads
    0

    Default Re: COLCHESTER TORNADO 80 alarm 1007

    Board is located either to the left of main A3 board or alternatively on right hand side panel
    Private message me your email and I will send you procedure



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

COLCHESTER TORNADO 80 alarm 1007

COLCHESTER TORNADO 80 alarm 1007

COLCHESTER TORNADO 80 alarm 1007