1990 Supermax TC2 Fanuc 0T control how to set parameters.


Results 1 to 11 of 11

Thread: 1990 Supermax TC2 Fanuc 0T control how to set parameters.

  1. #1
    Registered
    Join Date
    Apr 2009
    Location
    usa
    Posts
    95
    Downloads
    0
    Uploads
    0

    Default 1990 Supermax TC2 Fanuc 0T control how to set parameters.

    I just purchased this lathe. I have never worked with a Fanuc control. I am able to home and jog X and Z after homing x if I jog X+ I Move about 2" and hit the axis estop. I have found the parameter for this it is 50000 hundredths of a mm. It looks like it needs to be around 49000 hundredths of a mm. I do not know how to edit this field. There is a key switch on the front panel what does this do. The manuals are sketchy at best.

    Thank you for your help. Pictures of Control to follow.

    Jim

    Sent from my 831C using Tapatalk

    Similar Threads:
    Last edited by jbcj; 09-05-2015 at 11:09 PM.


  2. #2
    Member
    Join Date
    Dec 2009
    Location
    ROMANIA
    Posts
    507
    Downloads
    0
    Uploads
    0

    Default Re: 1990 Supermax TC2 Fanuc 0T control how to set parameters.

    you just need to make PWE=1 and you can adjust the parameter.



  3. #3
    Registered
    Join Date
    Apr 2009
    Location
    usa
    Posts
    95
    Downloads
    0
    Uploads
    0

    Default Re: 1990 Supermax TC2 Fanuc 0T control how to set parameters.

    Thank you for the information.

    I was able to change the X+ and Z- parameters. Now I am trying to figure out the zero on X . After homing I am able to move the X axis 2 inches in the pluse direction. Should the X axis after homing not be close to it's maximum plus. Is there another parameter that does this.

    Jim

    Sent from my 831C using Tapatalk



  4. #4
    Member
    Join Date
    Dec 2009
    Location
    ROMANIA
    Posts
    507
    Downloads
    0
    Uploads
    0

    Default Re: 1990 Supermax TC2 Fanuc 0T control how to set parameters.

    the zero position of an axes must be between 5-10 mm away from the emergency limit switch.
    after zero position should be soft overtravel on +(parameter 700,701,702) usual is 2.5 mm away from zero point and than remains about 5-7.5 mm untill the hard limit switch.



  5. #5
    Registered
    Join Date
    Apr 2009
    Location
    usa
    Posts
    95
    Downloads
    0
    Uploads
    0

    Default Re: 1990 Supermax TC2 Fanuc 0T control how to set parameters.

    Attached are some pictures of the Home proximity sensor and Estop limit switch. As you can see the homing sensor and the metal tab that are used for homing are 2" in the axis negative away from the Estop switch. so when i set parameter 0700 to 49500 this stops the axis just short of the Estop limit switch when jogging and I now get a X+ over limit instead of an Estop.. My position readout then reads approx +1.900 inches in the positive.

    Is there a parameter to correct this (move position 0.000 closer to the Estop switch)?

    Also on the control panel there is a key switch. What does this do?

    1990 Supermax TC2 Fanuc 0T control how to set parameters.-imag1045-jpg
    1990 Supermax TC2 Fanuc 0T control how to set parameters.-imag1046-jpg
    1990 Supermax TC2 Fanuc 0T control how to set parameters.-imag1047-jpg



  6. #6
    Member
    Join Date
    Dec 2009
    Location
    ROMANIA
    Posts
    507
    Downloads
    0
    Uploads
    0

    Default Re: 1990 Supermax TC2 Fanuc 0T control how to set parameters.

    Quote Originally Posted by jbcj View Post
    Attached are some pictures of the Home proximity sensor and Estop limit switch. As you can see the homing sensor and the metal tab that are used for homing are 2" in the axis negative away from the Estop switch. so when i set parameter 0700 to 49500 this stops the axis just short of the Estop limit switch when jogging and I now get a X+ over limit instead of an Estop.. My position readout then reads approx +1.900 inches in the positive.

    Is there a parameter to correct this (move position 0.000 closer to the Estop switch)?

    Also on the control panel there is a key switch. What does this do?

    1990 Supermax TC2 Fanuc 0T control how to set parameters.-imag1045-jpg
    1990 Supermax TC2 Fanuc 0T control how to set parameters.-imag1046-jpg
    1990 Supermax TC2 Fanuc 0T control how to set parameters.-imag1047-jpg
    it is normal operation.you should have an + overtravel limit switch before hitting the e-stop limit switch.
    you have on the panel the O.T release=Over Travel release-when, by accident,you hit the e-stop limit the O.T release button is bypassing the limit switch and let you jogging the axe in the opposite direction.

    for your question,yes.
    you need to change the parameter 21 and 22 like this

    you will have like this
    p21 00000011
    p22 00000011

    first you need to make the parameter 700 bigger than you have with ,let's say 50 mm
    than you jog the axe more closer to e-stop as you wish,better let 1 or 2 mm before hit the e-stop
    than make parameter 21 000000010 and parameter 22 the same 00000010
    power off and power on and than make parameter 22 00000011 and 21 00000011 and power off and power on.
    now you set the new reference point closer to e-stop
    you have now only 1 or 2 mm before hitting the e-stop and you need to set up the soft over travel limit by parameter 700 that will be in my opinion 1 mm if you have set up the home position more than 1 mm before hitting the e-stop.



  7. #7
    Registered
    Join Date
    Apr 2009
    Location
    usa
    Posts
    95
    Downloads
    0
    Uploads
    0

    Default Re: 1990 Supermax TC2 Fanuc 0T control how to set parameters.

    my parameter 21 00000000
    22 00000000

    I set them to: 00000001
    00000001

    I now have a: 310 error manual reference point return is required for X axis.
    and: 311 X - Axis APC Communications Error failure in data transmission.


    Thanks again for your help........


    Jim



  8. #8
    Registered
    Join Date
    Apr 2009
    Location
    usa
    Posts
    95
    Downloads
    0
    Uploads
    0

    Default Re: 1990 Supermax TC2 Fanuc 0T control how to set parameters.

    I returned P0021 and p0022 to 00000000

    and The 310 and 311 alarm went away but zero is still 1.9" away from estop switch.

    Jim



  9. #9
    Member
    Join Date
    Dec 2009
    Location
    ROMANIA
    Posts
    507
    Downloads
    0
    Uploads
    0

    Default Re: 1990 Supermax TC2 Fanuc 0T control how to set parameters.

    you should return the parameters after you move the table little closer



  10. #10
    Registered rshabodien's Avatar
    Join Date
    Feb 2019
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default Re: 1990 Supermax TC2 Fanuc 0T control how to set parameters.

    Quote Originally Posted by zavateandu View Post
    you should return the parameters after you move the table little closer
    Hi there

    seems i am in trouble. ive lost all the parameters for my machine after a power surge. can anyone help me?



  11. #11
    Registered
    Join Date
    Apr 2007
    Location
    USA
    Posts
    140
    Downloads
    0
    Uploads
    0

    Default

    *



  12. #12
    Reign3Knight's Avatar
    Join Date
    Feb 2019
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default

    hi i urgently need to parameter list of a Supermax Funac Series O-T .

    My email adress is ebrahim@arsteelworld.co.za

    i would really appreciate if some one could assist me ?



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

1990 Supermax TC2 Fanuc 0T control how to set parameters.

1990 Supermax TC2 Fanuc 0T control how to set parameters.