PMC-L OE1 and OE2 combining to #ex

[tc429]

hello
I need editing ladder of my machine with fanuc om controller.
I have eprom reader
can you help me
tanks

Fanuc PMC ROM Programmer | eBay
we bought one last yr, seems to do everything it says... only used it a couple times so far

[dh08td]

.....or, if anyone has OE1, OE2, and the corresponding #EX for a given ladder, I can figure it out from there if you're willing to share those three files.

can you share me the software how to converter the file.bin to file.#ex????
Thanks.
My mail: dien08td@gmail.com

[dh08td]

I wrote a QB program to combine the OE1 and OE2 files from Fanuc6 PLC and produce an output file looking like this:
1 RD 200.0
2 OR.NOT 200.0
3 WR 200.0
4 RD 65.7 MA NC>PC
5 WR 3.3 M18 PC>MT
6 RD 64.6 SA NC>PC
7 WR 3.0 M11 PC>MT
8 RD.NOT 38.4 *ESP MT>PC
9 WR 3.4 M21 PC>MT
10 RD 38.4 *ESP MT>PC
11 WR 102.4 *ESP PC>NC
12 RD 38.5 *SP MT>PC
13 AND 35.6 *SVF4 MT>PC
14 WR 102.5 *SP PC>NC
15 END.1 ---END OF HIGH LEVEL
16 RD 132.2
17 RD 2.2 SF PC>MT
18 RD 200.0
19 MOV SUBROUTINE 8
20 P1 0011
21 P2 0111
22 P3 64
23 P4 0
24 RD 200.0

I can send a copy of the .BAS program and would like to see a similar program for other Fanuc ladders.

Dear friend.
Can you share me the program converter rom Fanuc 6m to ladder??
My mail: dien08td@gmail.com
Thanks

[tmbruno28]

SO, FOR A FANUC 0 PMC-L
YOU NEED A FANUC ROM WRITER AND A FAPT LADDER WITH AN OLD VERSION 5 OR OLDER WITCH IS RUNNING FROM DOS ....

[tcom-frazzled]

Correct. You can use a generic EPROM reader/writer to read or write the individual chip images for things like backups, but the FA writer or PC writer and the DOS FAPT Ladder software is necessary if you need to create a single #EX that is needed to further decompile the ladder. The same is true for compiling, you can compile the code into a #EX, but splitting it onto OE1 and OE2 images requires the Fanuc reader/writer unit.

[dh08td]

Can you share me " UNSPLIT eeprom 6m"???
My mail: dien08td@gmail.com

[systronic]

Correct. You can use a generic EPROM reader/writer to read or write the individual chip images for things like backups, but the FA writer or PC writer and the DOS FAPT Ladder software is necessary if you need to create a single #EX that is needed to further decompile the ladder. The same is true for compiling, you can compile the code into a #EX, but splitting it onto OE1 and OE2 images requires the Fanuc reader/writer unit.

So I need a good guy with a Fanuc PC writer to help me if y want to modify my ladder ?

I know right we do not able to edit a ladder if we read it form other eprom programmer.
We need to use a Fanuc pc writer with a old dos computer (because a serial port needed and dos fladder programme) but i don't have a Fanuc pc writer.

I have already my OE1.bin And OE2.Bin files reddy to go and I want to activate drip feed G127.5 on my ladder,

Please someone can help me? My e-mail systronic@hotmail.com, Thanks !!

[zyazi]

Hello Friends.

I appreciate if someone that has the necessary equipment, can merge the attached eprom images and send the EX file to this mail : zyazi@hotmail.com

thanks in advance.

[ThienHa]

Hello Friends.

I appreciate if someone that has the necessary equipment, can merge the attached eprom images and send the EX file to this mail : zyazi@hotmail.com

thanks in advance.

Hi

Please send the picture of your main board with the position of OF1 and OF2 chip, may be I can help

[zyazi]

Hi

Please send the picture of your main board with the position of OF1 and OF2 chip, may be I can help

thanks for the reply.

attached, you will find the board picture..

[CNCtam]

Hi friends,

I am wondering if anyone can help me with the BIN data file of EPROM PMC 0E1 as below.

The machine is : CNC Lathe, Taitung TL-15S, Fanuc 0-TC

Unfortunately, the ROM was damaged and I need the data file for replacement. Thanks a lot for all help

[systronic]

Hello !

I think you need to find someone with the seam machine and have a copy of are ladder. Also the ladder is very specific to the machine so if you find it, it can be not york perfectly...

Have you tried to copy your EPROMs to a new one with a eprom programmer ?

Sorry for my English , I talk French

[CNCtam]

Hello !

I think you need to find someone with the seam machine and have a copy of are ladder. Also the ladder is very specific to the machine so if you find it, it can be not york perfectly...

Have you tried to copy your EPROMs to a new one with a eprom programmer ?

Sorry for my English , I talk French

Thanks a lot for your quick response! I well understood your recommendation

Yes, I also think the best is looking for the same machine, then copy the BIN file data into a new EPROM by Programmer. But unfortunately again, there is only that machine I've known until now, no other same machine I could find in the country. This is very specific machine type, the MTB Taitung no more handles this machine. I hope it exists somewhere in other countries that will help me with this case

Also, I have tried to copy data by EPROM Programmer to a new ROM already, but because the data is damaged, the new ROM made the same errors as the old one which is identical data copied.

The ROM is confirmed problem, as when I tested with other ROMs from a different machine, the machine could boot completely without error 998, but of course, it cannot run because the program inside different.

I hope to be lucky if someone has this data and will help me, then the problem will be solved perfectly

[systronic]

Ok, i think yo have to make a new post for it with alle information about your contrôler and machine. you can try to communicate with the machine bulder sometime it can work..., also, i dont know but if you can load it on fanuc ladder III,. It can be repaired ?!?

[CNCtam]

Sorry, I have not yet worked with Fanuc Ladder Programmer, as I heard it should have some tools which are necessary for editing. Do you know what tools and how to combine/convert 2 .BIN files 0E1 and 0E2 to a Fanuc Ladder file for editing or repairing any errors, then reconvert it to 2 BIN files for loading to EPROM? Fanuc Ladder III application can be used for that purpose? Where we can get that software? Thanks again.

[systronic]

It's depend of witch version of controler you have, if it's a 0M-C it can be easier than if you have a 0M-B,

[CNCtam]

The controller of machine I mentioned is 0-TC. So if I have 2 .BIN files of 0E1 and 0E2, I wondering if someone can help to convert them to a Ladder file so that can be eddied.

What Fanuc Ladder software can be used to edit this Ladder file? Thanks

[systronic]

I think for the c version you can use fanuc in ladder III,

[phucrobusl]

send me OE1 & OE2 FILES on rd181993@gmail.com i will convert a files for you.

[CNCtam]

send me OE1 & OE2 FILES on rd181993@gmail.com i will convert a files for you.

Thank you so much.
I have just sent you 2 files 0E1 & 0E2. Please help me to covert to Ladder files and remade 2 new 0E1 and 0E2
Very appreciate your help!