Fadal


Page 1 of 124 12341151101 ... LastLast
Threads 1 to 20 of 2461

Forum: Fadal

Discuss Fadal machinery here!

  1. Need Help!- can't get access to resolver on X axis motor

    Started by centaur91‎, 02-17-2019 05:42 PM
    • Replies: 2
    • Views: 107
    Yesterday, 01:57 PM Go to last post
  2. Need Help!- X axis fault Error #1 but gives error #3 when amp card swapped

    Started by centaur91‎, 02-17-2019 02:27 PM
    • Replies: 2
    • Views: 80
    Yesterday, 01:35 PM Go to last post
  3. Need Help!- installing new resolvers alignment

    Started by centaur91‎, 02-17-2019 04:48 PM
    alignment, axis, form, installed, resolvers
    • Replies: 2
    • Views: 104
    02-17-2019, 09:19 PM Go to last post
  4. GA4566-1 servo drive REPAIR or REPLACE

    Started by cogoman‎, 01-20-2009 11:55 AM
    1010-1, 1030-0, 595, keep, knows, plus, said
    • Replies: 3
    • Views: 1,122
    02-17-2019, 04:04 PM Go to last post
  5. G-Code check...

    Started by rwskinner‎, 02-14-2019 11:40 PM
    drill, g90, x2.7375, y-0.5, z0.8
    • Replies: 5
    • Views: 146
    02-15-2019, 02:17 PM Go to last post
  6. Fadal 4020 complete control system for sale

    Started by euroflo‎, 01-12-2019 07:11 PM
    control, fadal, problem, sell, system
    • Replies: 11
    • Views: 380
    02-14-2019, 07:45 PM Go to last post
  7. Need Help!- Axis amp replaced - now I get strange sound from axis motor

    Started by ginner‎, 02-07-2019 12:20 PM
    amp, axis, kind, lot, replaced
    • Replies: 4
    • Views: 162
    02-10-2019, 03:52 PM Go to last post
  8. Need Help!- OLD Bijur Mist Lubricator Issues/Parts/Literature/Manual

    Started by NismoGT‎, 02-04-2019 11:26 PM
    bijur, fadal, lubrication, oiler, vmc 40
    • Replies: 5
    • Views: 175
    02-08-2019, 01:07 PM Go to last post
  9. Need Help!- Travel Accuracy

    Started by bk1955‎, 01-28-2019 12:57 PM
    ideas, machine, part, travel, travels
    • Replies: 9
    • Views: 257
    02-08-2019, 11:19 AM Go to last post
  10. Question about lubrication requirements

    Started by mwbridgwater‎, 01-31-2019 06:59 PM
    lube, lubrication, lubricator, oil, spindle
    • Replies: 5
    • Views: 213
    02-06-2019, 11:38 AM Go to last post
  11. MAC Air Valves

    Started by rwskinner‎, 01-27-2019 11:44 PM
    • Replies: 3
    • Views: 154
    01-29-2019, 03:04 PM Go to last post
  12. C Axis Fault - Motor Overload

    Started by rwskinner‎, 01-26-2019 08:28 PM
    baldor, faults, inverter, motor, overload
    • Replies: 2
    • Views: 182
    01-29-2019, 02:51 PM Go to last post
  13. Troubleshooting New Glentek inverter issues.

    Started by destroyer125‎, 01-19-2019 11:08 PM
    bus, inverter, regen, resistors, spindle
    • Replies: 11
    • Views: 289
    01-24-2019, 09:50 PM Go to last post
  14. 1996 4020ht - new to me, much maintenance required

    Started by Deano7/11‎, 01-01-2019 07:02 AM
    4 Pages
    1 2 3 4
    • Replies: 40
    • Views: 1,072
    01-23-2019, 01:35 AM Go to last post
  15. Tool changer Slot assignment

    Started by rwskinner‎, 01-20-2019 11:23 AM
    assign, changer, number, slot, tool
    • Replies: 4
    • Views: 178
    01-21-2019, 07:33 PM Go to last post
  16. Question Can you raise the Z axis ???

    Started by Cfin‎, 01-16-2019 09:17 PM
    axis, column, extended, problems, rear
    • Replies: 8
    • Views: 273
    01-21-2019, 10:59 AM Go to last post
  17. NUMBER OUT OF RANGE

    Started by denmar‎, 01-18-2019 02:15 PM
    number, range, shows, table, tool
    • Replies: 0
    • Views: 101
    01-18-2019, 02:15 PM Go to last post
    • Replies: 4
    • Views: 171
    01-18-2019, 01:21 PM Go to last post
  18. Looking at buying a Fadal

    Started by rwskinner‎, 12-06-2018 05:39 PM
    6 Pages
    1 2 3 4 5 ... 6
    • Replies: 66
    • Views: 1,934
    01-17-2019, 09:48 PM Go to last post
  19. Need Help!- Houston area Fadal repair company

    Started by KENNY D‎, 01-17-2019 01:40 PM
    area, company, fadal, houston, repair
    • Replies: 0
    • Views: 110
    01-17-2019, 01:40 PM Go to last post

Page 1 of 124 12341151101 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 6 users browsing this forum. (0 members & 6 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands