VMC15 XT motor pulley and spindle pulley


Results 1 to 7 of 7

Thread: VMC15 XT motor pulley and spindle pulley

  1. #1
    Member
    Join Date
    Feb 2014
    Location
    USA
    Posts
    182
    Downloads
    0
    Uploads
    0

    Default VMC15 XT motor pulley and spindle pulley

    Hello I am looking to see if any can tell me the depth of the pulley when mounting to the spindle motor and depth of pulley to the spindle? Have new motor, spindle and both new cog pulleys. This is for a VMC15 XT 7500rpm spindle.

    Thanks for the help

    Similar Threads:


  2. #2
    Member
    Join Date
    Oct 2008
    Location
    United States
    Posts
    1549
    Downloads
    0
    Uploads
    0

    Default Re: VMC15 XT motor pulley and spindle pulley

    Let me take a look......

    Attached Thumbnails Attached Thumbnails VMC15 XT motor pulley and spindle pulley-spindle1-jpg   VMC15 XT motor pulley and spindle pulley-spindle2-jpg  


  3. #3
    Member
    Join Date
    Feb 2014
    Location
    USA
    Posts
    182
    Downloads
    0
    Uploads
    0

    Default Re: VMC15 XT motor pulley and spindle pulley

    I appreciate you taking a look. I can't find anywhere in the manual that says the distances for the gates power cog pulleys. I think from the motor shaft end to the bottom of the pulley is .43". Would like to know for sure because you have to pull the motor back off to move the pulley. I think the spindle pulley is flush with the top of the inside of the pulley and the spindle shaft where the line markings are for the orientation.



  4. #4
    Member
    Join Date
    Oct 2008
    Location
    United States
    Posts
    1549
    Downloads
    0
    Uploads
    0

    Default Re: VMC15 XT motor pulley and spindle pulley

    Those were the only measurements I had but maybe someone else can help with the dimensions you need.
    I snagged those a while back in case I ever needed them later. Hopefully not, famous last words.



  5. #5
    Member
    Join Date
    Oct 2013
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default Re: VMC15 XT motor pulley and spindle pulley

    if its a 7500 rpm pulley it should be the gates "poly chain" belt, and spacing. Unless you've got an odd belt setup, i've never seen a cogged belt on a fadal



  6. #6
    Member
    Join Date
    Feb 2014
    Location
    USA
    Posts
    182
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by tenchuuu View Post
    if its a 7500 rpm pulley it should be the gates "poly chain" belt, and spacing. Unless you've got an odd belt setup, i've never seen a cogged belt on a fadal
    I meant to say Gates “Poly Chain.” Thanks for correcting.



  7. #7
    Member machinehop5's Avatar
    Join Date
    Aug 2009
    Location
    United States
    Posts
    1050
    Downloads
    4
    Uploads
    2

    Default Re: VMC15 XT motor pulley and spindle pulley

    ..spacely sockets aka.. and a boy named elroy. in the passed



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

VMC15 XT motor pulley and spindle pulley

VMC15 XT motor pulley and spindle pulley

VMC15 XT motor pulley and spindle pulley