Tapping program question


Results 1 to 5 of 5

Thread: Tapping program question

  1. #1

    Default Tapping program question

    Regarding a 1993 Fadal VMC3016 with rigid tapping:
    If I have an M1 after tapping a hole to a particular depth (To blow out chips/oil), can I program to go back in a second time (deeper) and expect the machine to stay synchronized with the thread it just cut previously?

    Similar Threads:


  2. #2
    Member
    Join Date
    Aug 2007
    Location
    USA
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default Re: Tapping program question

    The 3 Fadals I have had would retap a hole perfectly as long as I didn't change tools. Best rigid tapping machine I have.

    All my other CNCs (Matsuura, Kitamura, Haas) would open up the thread and the no-go gage would go if I programmed a second cycle on a previously tapped hole with a deeper Z depth.



  3. #3

    Default Re: Tapping program question

    Thanks, Larry - interesting about the Fadal being more precise than the others.

    I didn't get an answer here soon enough, so I just went ahead and experimented. Found some peck tapping programs online, combined some ideas from different ones, and made my own changes I found to be necessary. Works great. I squirt cutting oil in the hole with a syringe from the bottom up until its full, then tap to Z-.600; M1 to blow out chips with a tube into the bottom of the hole (Z waiting at +.300) and fill the hole with oil again; "Start" and tap to Z-.850; M1 again to blow out chips and fill the next hole with oil; Etc. I found I had to add the spindle speed after every M45 and second Z depth for the program to work right - was all funky before I did that. Here's what I ended up with:

    N1 G17 G20 G40 G49 G80
    N2 T04 M06 (1/4-28 spiral point tap)
    N3 G00 G90 G54 X__ Y__
    N4 S1000 M5
    N5 G43 H04 Z.3
    N6 G84.1 G99 R0+.3 Z-.600 S1000.2 F35.714 (Rigid tap)
    N7 M01
    N8 M45 Z-.850 S1000.2
    N9 M01


    N10 G80 X__
    N11 G84.1 G99 R0+.3 Z-.600 S1000.2 F35.714
    N12 M01
    N13 M45 Z-.850 S1000.2
    N14 M01


    N15 G80 X__
    N16 G84.1 G99 R0+.3 Z-.600 S1000.2 F35.714
    N17 M01
    N18 M45 Z-.850 S1000.2
    N19 M01


    N20 G80 X__
    N21 G84.1 G99 R0+.3 Z-.600 S1000.2 F35.714
    N22 M01
    N23 M45 Z-.850 S1000.2
    N24 M01

    Etc., X 10 holes, in my case

    Mark



  4. #4
    Member
    Join Date
    Mar 2008
    Location
    USA
    Posts
    683
    Downloads
    0
    Uploads
    0

    Default Re: Tapping program question

    I'm too paranoid to use rigid peck tapping on my fadals. Broke a tap in very expensive part so i don't do that anymore. But good to hear about Larry's results.



  5. #5
    Member ASIGuy's Avatar
    Join Date
    Feb 2007
    Location
    USA
    Posts
    171
    Downloads
    0
    Uploads
    0

    Default Re: Tapping program question

    Warrenb, setting up and testing your RT is quite easy. You only need a rigid tapping test tool (SVT-0077- $75 in stock), put in a collet holder and run a short rigid tapping program while you have an indicator in the threads watching for deviation. You should be able to adjust Gain and Ramp in the parameters until you get it tight as you need. We have a video on our web site showing how to do this. I also have a test Rigid tapping program I can send you for the test and adjustment.

    Let me know how or if I can help.
    FadalCNC Support



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Tapping program question

Tapping program question