EZ Router


Page 1 of 2 12 LastLast
Threads 1 to 20 of 21

Forum: EZ Router

Discuss EZ routers here.

  1. Scorpion not holding z

    Started by SaberMike‎, 02-18-2020 01:13 PM
    scorpion, z axis
    • Replies: 0
    • Views: 479
    02-18-2020, 01:13 PM Go to last post
  2. Problem- Bad breakout board on Scorpion 5 x 10 Wood Router?

    Started by rfeist11‎, 02-12-2017 08:16 AM
    • Replies: 9
    • Views: 2,457
    10-02-2017, 07:27 PM Go to last post
    • Replies: 2
    • Views: 3,350
    09-17-2017, 04:47 PM Go to last post
  3. Need EZ Router Repair Help

    Started by AndyBC‎, 08-15-2017 02:46 PM
    finally, forum, machine, repair, software
    • Replies: 0
    • Views: 859
    08-15-2017, 02:46 PM Go to last post
  4. EZ Router Binding

    Started by dameronw‎, 07-13-2017 12:02 PM
    added, end, homing, ipm, router
    • Replies: 3
    • Views: 862
    07-13-2017, 01:47 PM Go to last post
  5. Need Help!- Ez Router Scorpion and Mach3

    Started by rfeist11‎, 01-18-2017 12:46 PM
    axis, estop, mach3, pin, router
    • Replies: 2
    • Views: 1,166
    01-19-2017, 06:17 PM Go to last post
  6. Need Help!- Auto z on e-zrouter nuts help

    Started by Max Richards‎, 10-26-2016 08:50 PM
    e-zrouter, hits, limit, plate, switch
    • Replies: 0
    • Views: 949
    10-26-2016, 08:50 PM Go to last post
  7. EZ Router Problems

    Started by wesandkim‎, 04-20-2016 10:12 AM
    clips, fixes, machine, router, tool
    • Replies: 0
    • Views: 1,384
    04-20-2016, 10:12 AM Go to last post
  8. Need Help!- Help me add a 4th axis to my EZ-Router

    Started by Mootsman‎, 02-11-2016 10:59 AM
    • Replies: 13
    • Views: 3,129
    02-21-2016, 04:14 PM Go to last post
  9. ezrouter

    Started by moolidhaar‎, 08-11-2015 11:26 AM
    appreciated, ezrouter, greatly, running, set
    • Replies: 0
    • Views: 1,584
    08-11-2015, 11:26 AM Go to last post
  10. Problem- 2006 machine motors are out of sync

    Started by greggm‎, 08-04-2014 09:34 PM
    • Replies: 1
    • Views: 1,905
    08-06-2014, 11:20 PM Go to last post
  11. EZ-ROUTER 4X4

    Started by sandingsucks‎, 01-24-2014 08:46 AM
    far, went
    • Replies: 6
    • Views: 2,965
    04-13-2014, 11:50 PM Go to last post
  12. Newbie- Buying CNC ?

    Started by sandingsucks‎, 11-15-2013 12:21 AM
    • Replies: 4
    • Views: 3,035
    02-10-2014, 12:32 AM Go to last post
  13. EZ Router The Boss

    Started by MarshallPlexi‎, 04-20-2013 10:49 PM
    near
    • Replies: 0
    • Views: 3,245
    04-20-2013, 10:49 PM Go to last post
  14. Our most recent Scorpion

    Started by ezRouter‎, 06-29-2012 05:15 PM
    • Replies: 0
    • Views: 3,381
    06-29-2012, 05:15 PM Go to last post
  15. Beginning APC Model Discounts! Up to $3000 Off!

    Started by ezRouter‎, 06-14-2012 02:02 PM
    available, cnc-plasma, look, regards
    • Replies: 0
    • Views: 2,729
    06-14-2012, 02:02 PM Go to last post
  16. ezRouter Forum is Here!

    Started by ezRouter‎, 06-08-2012 05:36 PM
    look
    • Replies: 0
    • Views: 2,926
    06-08-2012, 05:36 PM Go to last post
  17. Ez-Router Serial Port

    Started by Robert Garrett‎, 09-23-2011 04:34 PM
    • Replies: 1
    • Views: 3,627
    10-03-2011, 07:12 PM Go to last post
  18. Poll Poll: Ez Flex vs Comet

    Started by Pawelski‎, 09-17-2011 08:44 PM
    next
    • Replies: 0
    • Views: 4,460
    09-17-2011, 08:44 PM Go to last post
  19. EZ Router and Scorpion owners?

    Started by OnekiKai‎, 05-23-2011 09:58 AM
    cabine
    • Replies: 1
    • Views: 5,854
    06-10-2011, 09:02 AM Go to last post

Page 1 of 2 12 LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 2 users browsing this forum. (0 members & 2 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands