Dynomotion/Kflop/Kanalog - Page 4


Page 4 of 50 FirstFirst 123456714 ... LastLast
Threads 61 to 80 of 981

Forum: Dynomotion/Kflop/Kanalog

Discuss Dynomotion/Kflop/Kanalog here!

  1. Updated drawing

    Started by mirocha‎, 11-19-2018 10:35 AM
    • Replies: 1
    • Views: 238
    11-19-2018, 12:11 PM Go to last post
  2. Closed loop feedback to glass linear encoders

    Started by men8ifr‎, 10-24-2018 01:18 PM
    2 Pages
    1 2
    • Replies: 12
    • Views: 744
    11-18-2018, 04:07 AM Go to last post
  3. Need Help!- How to get and set offsets for U and V axes

    Started by amitkumar171‎, 11-12-2018 11:56 PM
    • Replies: 1
    • Views: 284
    11-16-2018, 12:31 AM Go to last post
  4. Kflop dont boot up

    Started by mk00‎, 11-14-2018 12:28 AM
    burning, constantly, diodes, kflop, reason
    • Replies: 2
    • Views: 187
    11-14-2018, 12:52 AM Go to last post
  5. ouput signal

    Started by dmoglianesi‎, 09-27-2018 01:54 PM
    2 Pages
    1 2
    0/360, axes, degrees, format, rotational
    • Replies: 13
    • Views: 552
    11-04-2018, 12:22 PM Go to last post
  6. Need Help!- G43 G49 status Led and Toggle

    Started by dirtdigger257‎, 11-01-2018 09:44 PM
    • Replies: 3
    • Views: 234
    11-04-2018, 12:05 PM Go to last post
  7. Problem with Y axis, need help!!

    Started by mmurray70‎, 10-27-2018 05:09 PM
    • Replies: 9
    • Views: 381
    10-28-2018, 08:53 PM Go to last post
  8. help urgent

    Started by dmoglianesi‎, 10-16-2018 05:14 PM
    dalmazio, moglianesi, send, test, week
    • Replies: 10
    • Views: 343
    10-25-2018, 04:22 AM Go to last post
  9. Dual loop intput interconnect

    Started by funding33‎, 10-22-2018 05:14 PM
    • Replies: 1
    • Views: 168
    10-23-2018, 12:48 PM Go to last post
  10. How to abort MoveExp()

    Started by funding33‎, 10-19-2018 04:43 PM
    abort, ch2-output, ch2-output;, disturbances, moveexp
    • Replies: 1
    • Views: 164
    10-19-2018, 05:15 PM Go to last post
  11. Need Help!- Control commands for the microcontroller.

    Started by zaxtone‎, 08-31-2018 01:00 PM
    atmega128, commands, control, microcontroller, output
    • Replies: 10
    • Views: 492
    10-15-2018, 06:34 PM Go to last post
  12. Need Help!- Regarding encoder input to kflop

    Started by amitkumar171‎, 09-14-2018 06:47 AM
    2 Pages
    1 2
    • Replies: 12
    • Views: 582
    10-11-2018, 11:28 AM Go to last post
  13. Lightbulb kflop for robot

    Started by huynguyen93‎, 10-05-2018 12:03 AM
    • Replies: 0
    • Views: 422
    10-05-2018, 12:03 AM Go to last post
  14. Question Questions for TomK re. Linux and Kanalog

    Started by Toneski‎, 10-02-2018 07:39 AM
    linux, questions, tom, version, wine linux
    • Replies: 4
    • Views: 291
    10-03-2018, 11:36 AM Go to last post
  15. Screen editor --- Unhandled exception

    Started by todmorg‎, 09-30-2018 10:38 PM
    • Replies: 5
    • Views: 200
    10-01-2018, 12:14 PM Go to last post
    • Replies: 1
    • Views: 267
    09-30-2018, 12:42 PM Go to last post
  16. Viewing console from KmotionCNC

    Started by mmurray70‎, 08-30-2018 10:42 AM
    2 Pages
    1 2
    • Replies: 20
    • Views: 679
    09-28-2018, 11:09 AM Go to last post
  17. Need Help!- How to use all 8 Axes in Kflop Board Connected with Kanalog Board

    Started by amitkumar171‎, 09-07-2017 10:00 AM
    2 Pages
    1 2
    • Replies: 12
    • Views: 915
    09-24-2018, 01:57 AM Go to last post
  18. Need Help!- Instruction on Knozz wiring and setup

    Started by amitkumar171‎, 10-18-2017 03:15 AM
    4 Pages
    1 2 3 4
    • Replies: 37
    • Views: 2,087
    09-20-2018, 12:24 PM Go to last post
  19. Flexicam ATC router retrofit with Kflop/Kanalog

    Started by xyz-cnc‎, 09-06-2018 09:06 AM
    3 Pages
    1 2 3
    • Replies: 33
    • Views: 988
    09-18-2018, 04:16 PM Go to last post

Page 4 of 50 FirstFirst 123456714 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 19 users browsing this forum. (2 members & 17 guests)

  1. greggv,
  2. mmurray70

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands