Dynomotion/Kflop/Kanalog - Page 2


Page 2 of 48 FirstFirst 1234512 ... LastLast
Threads 21 to 40 of 944

Forum: Dynomotion/Kflop/Kanalog

Discuss Dynomotion/Kflop/Kanalog here!

  1. Need Help!- G43 G49 status Led and Toggle

    Started by dirtdigger257‎, 11-01-2018 10:44 PM
    • Replies: 3
    • Views: 186
    11-04-2018, 01:05 PM Go to last post
  2. Kflop Board not seen by Kmotion

    Started by spank‎, 10-29-2018 06:39 PM
    board, installed, kflop, kmotion, software
    • Replies: 6
    • Views: 179
    10-30-2018, 03:54 PM Go to last post
  3. Problem with Y axis, need help!!

    Started by mmurray70‎, 10-27-2018 06:09 PM
    • Replies: 9
    • Views: 252
    10-28-2018, 09:53 PM Go to last post
  4. help urgent

    Started by dmoglianesi‎, 10-16-2018 06:14 PM
    dalmazio, moglianesi, send, test, week
    • Replies: 10
    • Views: 322
    10-25-2018, 05:22 AM Go to last post
  5. Dual loop intput interconnect

    Started by funding33‎, 10-22-2018 06:14 PM
    • Replies: 1
    • Views: 125
    10-23-2018, 01:48 PM Go to last post
  6. Does KmotionCNC simulator support trajectory planner?

    Started by funding33‎, 10-07-2018 03:44 PM
    2 Pages
    1 2
    • Replies: 18
    • Views: 512
    10-22-2018, 06:11 PM Go to last post
  7. How to abort MoveExp()

    Started by funding33‎, 10-19-2018 05:43 PM
    abort, ch2-output, ch2-output;, disturbances, moveexp
    • Replies: 1
    • Views: 141
    10-19-2018, 06:15 PM Go to last post
  8. DSP_Kmotion.out Date Stamp

    Started by purple_jeep‎, 10-18-2018 01:52 PM
    • Replies: 2
    • Views: 126
    10-18-2018, 04:19 PM Go to last post
  9. Need Help!- Control commands for the microcontroller.

    Started by zaxtone‎, 08-31-2018 02:00 PM
    atmega128, commands, control, microcontroller, output
    • Replies: 10
    • Views: 449
    10-15-2018, 07:34 PM Go to last post
  10. Lightbulb kflop for robot

    Started by huynguyen93‎, 10-05-2018 01:03 AM
    • Replies: 6
    • Views: 338
    10-15-2018, 12:50 PM Go to last post
  11. Need Help!- Regarding encoder input to kflop

    Started by amitkumar171‎, 09-14-2018 07:47 AM
    2 Pages
    1 2
    • Replies: 12
    • Views: 487
    10-11-2018, 12:28 PM Go to last post
  12. Question Questions for TomK re. Linux and Kanalog

    Started by Toneski‎, 10-02-2018 08:39 AM
    linux, questions, tom, version, wine linux
    • Replies: 4
    • Views: 248
    10-03-2018, 12:36 PM Go to last post
  13. Screen editor --- Unhandled exception

    Started by todmorg‎, 09-30-2018 11:38 PM
    • Replies: 5
    • Views: 168
    10-01-2018, 01:14 PM Go to last post
    • Replies: 1
    • Views: 186
    09-30-2018, 01:42 PM Go to last post
  14. Viewing console from KmotionCNC

    Started by mmurray70‎, 08-30-2018 11:42 AM
    2 Pages
    1 2
    • Replies: 20
    • Views: 609
    09-28-2018, 12:09 PM Go to last post
  15. Need Help!- How to use all 8 Axes in Kflop Board Connected with Kanalog Board

    Started by amitkumar171‎, 09-07-2017 11:00 AM
    2 Pages
    1 2
    • Replies: 12
    • Views: 816
    09-24-2018, 02:57 AM Go to last post
  16. Need Help!- Instruction on Knozz wiring and setup

    Started by amitkumar171‎, 10-18-2017 04:15 AM
    4 Pages
    1 2 3 4
    • Replies: 37
    • Views: 1,908
    09-20-2018, 01:24 PM Go to last post
  17. Flexicam ATC router retrofit with Kflop/Kanalog

    Started by xyz-cnc‎, 09-06-2018 10:06 AM
    3 Pages
    1 2 3
    • Replies: 33
    • Views: 825
    09-18-2018, 05:16 PM Go to last post
  18. Problem- KmotionCNC DRO flashing yellow/blue while running gcode

    Started by MadTooler‎, 09-17-2018 07:03 PM
    dro, kmotioncnc, normal, router, running
    • Replies: 2
    • Views: 192
    09-17-2018, 07:43 PM Go to last post
  19. Watchdog FET

    Started by itme‎, 09-13-2018 10:57 AM
    • Replies: 2
    • Views: 133
    09-13-2018, 04:06 PM Go to last post

Page 2 of 48 FirstFirst 1234512 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 19 users browsing this forum. (1 members & 18 guests)

  1. Causeitso

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands