Dynomotion/Kflop/Kanalog


Page 1 of 47 123411 ... LastLast
Threads 1 to 20 of 935

Forum: Dynomotion/Kflop/Kanalog

Discuss Dynomotion/Kflop/Kanalog here!

  1. Updated drawing

    Started by mirocha‎, Today 11:35 AM
    • Replies: 1
    • Views: 68
    Today, 01:11 PM Go to last post
  2. G code error

    Started by mirocha‎, 10-28-2018 08:00 PM
    2 Pages
    1 2
    • Replies: 17
    • Views: 464
    Today, 09:25 AM Go to last post
  3. Closed loop feedback to glass linear encoders

    Started by men8ifr‎, 10-24-2018 02:18 PM
    2 Pages
    1 2
    • Replies: 12
    • Views: 381
    Yesterday, 05:07 AM Go to last post
  4. SBL Magnaturn Retrofit

    Started by Need TECH Help!‎, 06-24-2018 11:47 AM
    7 Pages
    1 2 3 4 5 ... 7
    • Replies: 75
    • Views: 1,889
    11-17-2018, 08:57 PM Go to last post
  5. G code viewer questions...

    Started by mmurray70‎, 10-21-2018 08:47 PM
    • Replies: 11
    • Views: 383
    11-16-2018, 04:07 PM Go to last post
  6. Need Help!- How to get and set offsets for U and V axes

    Started by amitkumar171‎, 11-13-2018 12:56 AM
    • Replies: 1
    • Views: 120
    11-16-2018, 01:31 AM Go to last post
  7. Kflop dont boot up

    Started by mk00‎, 11-14-2018 01:28 AM
    burning, constantly, diodes, kflop, reason
    • Replies: 2
    • Views: 76
    11-14-2018, 01:52 AM Go to last post
  8. Build Thread- Tree325 Retrofit Started

    Started by PeterTheWolf‎, 09-24-2017 08:10 PM
    26 Pages
    1 2 3 4 5 ... 26
    • Replies: 302
    • Views: 16,010
    11-12-2018, 02:45 PM Go to last post
  9. ouput signal

    Started by dmoglianesi‎, 09-27-2018 02:54 PM
    2 Pages
    1 2
    0/360, axes, degrees, format, rotational
    • Replies: 13
    • Views: 451
    11-04-2018, 01:22 PM Go to last post
  10. Need Help!- G43 G49 status Led and Toggle

    Started by dirtdigger257‎, 11-01-2018 10:44 PM
    • Replies: 3
    • Views: 164
    11-04-2018, 01:05 PM Go to last post
  11. Kflop Board not seen by Kmotion

    Started by spank‎, 10-29-2018 06:39 PM
    board, installed, kflop, kmotion, software
    • Replies: 6
    • Views: 149
    10-30-2018, 03:54 PM Go to last post
  12. Problem with Y axis, need help!!

    Started by mmurray70‎, 10-27-2018 06:09 PM
    • Replies: 9
    • Views: 230
    10-28-2018, 09:53 PM Go to last post
  13. help urgent

    Started by dmoglianesi‎, 10-16-2018 06:14 PM
    dalmazio, moglianesi, send, test, week
    • Replies: 10
    • Views: 311
    10-25-2018, 05:22 AM Go to last post
  14. Dual loop intput interconnect

    Started by funding33‎, 10-22-2018 06:14 PM
    • Replies: 1
    • Views: 110
    10-23-2018, 01:48 PM Go to last post
  15. Does KmotionCNC simulator support trajectory planner?

    Started by funding33‎, 10-07-2018 03:44 PM
    2 Pages
    1 2
    • Replies: 18
    • Views: 498
    10-22-2018, 06:11 PM Go to last post
  16. How to abort MoveExp()

    Started by funding33‎, 10-19-2018 05:43 PM
    abort, ch2-output, ch2-output;, disturbances, moveexp
    • Replies: 1
    • Views: 135
    10-19-2018, 06:15 PM Go to last post
  17. DSP_Kmotion.out Date Stamp

    Started by purple_jeep‎, 10-18-2018 01:52 PM
    • Replies: 2
    • Views: 116
    10-18-2018, 04:19 PM Go to last post
  18. Need Help!- Control commands for the microcontroller.

    Started by zaxtone‎, 08-31-2018 02:00 PM
    atmega128, commands, control, microcontroller, output
    • Replies: 10
    • Views: 435
    10-15-2018, 07:34 PM Go to last post
  19. Lightbulb kflop for robot

    Started by huynguyen93‎, 10-05-2018 01:03 AM
    • Replies: 6
    • Views: 322
    10-15-2018, 12:50 PM Go to last post

Page 1 of 47 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 20 users browsing this forum. (1 members & 19 guests)

  1. Ftian

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands