Need Help! Traub TND 254 - Page 2


Page 2 of 2 FirstFirst 12
Results 21 to 31 of 31

Thread: Traub TND 254

  1. #21

    Default Re: Traub TND 254

    now i`m working for the external control . FRO SSO and Rapid OVR

    i need to start the .c program manualy ( it`s running on thread 6). i don`t know why it`s doing that....

    Attached Files Attached Files


  2. #22

    Default Re: Traub TND 254



    Sent from my SM-A705FN using Tapatalk



  3. #23

    Default Re: Traub TND 254

    This is annoying.... why


    Attached Files Attached Files


  4. #24
    Member TomKerekes's Avatar
    Join Date
    May 2006
    Location
    USA
    Posts
    3335
    Downloads
    0
    Uploads
    0

    Default Re: Traub TND 254

    Hi swatcat,

    Did you Flash the correct program into Thread #6?

    Actually we don't recommend Flashing anything into KFLOP for exactly this reason. It becomes confusing to remember all the things that were done to KFLOP and what its current state is. Its simpler to keep KFLOP in a Virgin state and have the PC load what is needed as it is needed. KFLOP can be restored to its virgin state by re-Flashing using the "New Version" button.

    Its also preferred to use less Threads by combining all the things that must be serviced continuously into one forever loop in your Initialization Program that runs in Thread #1. Its often good to run things in separate Threads for debugging but once working they can be combined into one Thread. It looks like you have 5 Threads running? Are you able to do this? You might read this.

    You might also cleanup and indent your programs properly to make them easier to read and understand. A context menu option was added in V4.34a to do this automatically. See here.

    Regards
    TK http://dynomotion.com


  5. #25

    Default Re: Traub TND 254

    Now i'm running all the threads for testing reasons. In the final version i will merge all of them in one file.

    Yes. The program it's compiled and downloaded to thread 6.

    I've imported open c Program (thread 6) and flashed it again.

    Now it's working.THX

    Sent from my SM-A705FN using Tapatalk



  6. #26
    Registered
    Join Date
    Oct 2017
    Location
    Poland
    Posts
    2
    Downloads
    0
    Uploads
    0

    Default Re: Traub TND 254

    Hi ALL

    I would like to get schema how to make cable for connect with PC 9 PIN with TRAUB TND 200. I saw some one have a SERVICE book in english.I is possible to share the schema page ?
    Many Thanks in advance.



  7. #27

    Default Re: Traub TND 254



    I have some problems with G95 feed per revolution

    FRO it`s not changing the feed value

    When i change SSO, Kmotion freezes or give a error.

    What i am doing wrong?



    https://www.haascnc.com/service/code...value=G95.html



  8. #28

    Default Re: Traub TND 254

    and Feed Hold not working, Program HALT stopping after Look Ahead time (2s)



  9. #29
    Member TomKerekes's Avatar
    Join Date
    May 2006
    Location
    USA
    Posts
    3335
    Downloads
    0
    Uploads
    0

    Default Re: Traub TND 254

    Hi swat cat,

    What Version of KMotion are you using?

    Feed hold stops in the worst case stopping time for all the axes in the Coordinated Motion System. A common problem is to have a KFLOP Axis configured in an odd manner (high velocity and low acceleration or Jerk).

    Please post your C Programs and how KMotionCNC Tool Setup is configured.

    Regards
    TK http://dynomotion.com


  10. #30

    Default Re: Traub TND 254

    4.34, i've been waiting for the official version of 4.35.

    In normal motion g0 ,g1 feed hold and motion halt works instatenous.


    Tool setup is the same as in post #17

    Sent from my SM-A705FN using Tapatalk



  11. #31

    Default Re: Traub TND 254

    this 4 are running until i make a version of them in one file

    Attached Files Attached Files


  12. #32

    Default Re: Traub TND 254

    I've installed version 3.35b. The same problem.

    It's not ok.

    https://m.youtube.com/watch?feature=...&v=GiAq29AssoM

    Sent from my SM-A705FN using Tapatalk



Page 2 of 2 FirstFirst 12

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Traub TND 254

Traub TND 254

Traub TND 254