Need Help! How to make alive my pneumo-relay


Results 1 to 4 of 4

Thread: How to make alive my pneumo-relay

  1. #1
    Member RuslanRobot's Avatar
    Join Date
    May 2019
    Posts
    14
    Downloads
    0
    Uploads
    0

    Default How to make alive my pneumo-relay

    Please help!
    I dont understand - how to make alive my pneumo-relay.
    I have KFLOP + Konnect Optical I/O Expansion Board.

    Pneumo-relay connected to Konnect pins Out 12, 13, 14, 15.
    In the Kmotion -> Digital I/O -> Virtual, I see flags opposit connected pins.

    In the KmotionCNC -> M100-M119, I set I/O Bit. That is all.
    What to do next?

    I need commands in G code to turn on and off relay:
    M100 turn on relay pin12.
    M101 turn off relay pin12.
    M102 turn on relay pin13.
    M103 turn off relay pin13 (and so on, to pin15).

    How to do it? - in order Konnect understand G code ond do on/off relay

    Similar Threads:
    Attached Thumbnails Attached Thumbnails How to make alive my pneumo-relay-kflop-jpg  


  2. #2
    Member TomKerekes's Avatar
    Join Date
    May 2006
    Location
    USA
    Posts
    3130
    Downloads
    0
    Uploads
    0

    Default Re: How to make alive my pneumo-relay

    Hi RuslanRobot,

    Pneumo-relay connected to Konnect pins Out 12, 13, 14, 15.
    In the Kmotion -> Digital I/O -> Virtual, I see flags opposit connected pins.
    I don't understand. If you toggle Virtual Bit 60 on the KMotion | Digital IO | Virtual Screen does the Pneumo-relay toggle on and off?

    need commands in G code to turn on and off relay:
    M100 turn on relay pin12.
    M101 turn off relay pin12.
    M102 turn on relay pin13.
    M103 turn off relay pin13 (and so on, to pin15).
    If so, this is how you might configure your MCodes:

    How to make alive my pneumo-relay-iobits-png

    Please remember to put reverse flyback diodes across any solenoid or relay coils.

    Regards
    TK http://dynomotion.com


  3. #3
    Member RuslanRobot's Avatar
    Join Date
    May 2019
    Posts
    14
    Downloads
    0
    Uploads
    0

    Default Re: How to make alive my pneumo-relay

    Yes!!!
    I did in accordance with your screen shot, and I can turn on/of lights on the board by G-code (M100 - lights on, M101 - lights off).

    But I connected relay to the Konnect without flyback diodes and relay doesn't click.
    Is it mean that I burned out all board Konnect, or only pins 12 - 15?



  4. #4
    Member TomKerekes's Avatar
    Join Date
    May 2006
    Location
    USA
    Posts
    3130
    Downloads
    0
    Uploads
    0

    Default Re: How to make alive my pneumo-relay

    Hi RuslanRobot,

    I connected relay to the Konnect without flyback diodes and relay doesn't click.
    How did you wire it? The Konnect outputs are like an isolated switch contact. You must have a power supply to apply power to a relay. Also the outputs will only conduct one direction like a diode.


    Is it mean that I burned out all board Konnect, or only pins 12 - 15?
    The Output circuits are all optically isolated so damaging one is unlikely to damage another.

    Regards
    TK http://dynomotion.com


Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

How to make alive my pneumo-relay

How to make alive my pneumo-relay