Need Help! New 64 bit computer....need help


Results 1 to 5 of 5

Thread: New 64 bit computer....need help

  1. #1
    Registered
    Join Date
    May 2015
    Location
    USA
    Posts
    3
    Downloads
    0
    Uploads
    0

    Angry New 64 bit computer....need help

    I bought an old DynaCNC table with a Dyna1000-THC controller (didn't know they were defunct) and was just getting it kind of figured out, when the 10 year old computer decided to fry itself.

    I did what any newbie would have done and bought a new computer. Now for my problems....

    Mach 3 won't run on 64 bit, so I bought Mach4.....Apparently Mach doesn't really like to pay anyone to offer tech support to its customers. It appears that I need some sort of plugin and need to setup the software to run the control box.

    Have any of you been through this and can lead me to a manual that will give me some direction. I am very green with this stuff.

    I am about $10,000 into this adventure so far, I am frustrated to say the least.

    Similar Threads:
    It's not WHAT you know, but WHO you know......


  2. #2
    Registered
    Join Date
    Sep 2013
    Posts
    15
    Downloads
    0
    Uploads
    0

    Default Re: New 64 bit computer....need help

    I have Mach3 installed and running on my development PC which is windows 7 64bit, however I have not connected to a CNC controller. So I guess some 64bit systems it may work.

    This might be a bit of a pain to do (and may not work) but you could try running an emulator so the 64 bit pretends it is a 32 bit PC:

    From Microsoft: "WOW64 is the x86 emulator that allows 32-bit Windows-based applications to run seamlessly on 64-bit Windows"
    https://msdn.microsoft.com/en-us/lib...=vs.85%29.aspx

    Or you could try running in XP mode (I have used this to run programs that would not run on WIN7):
    Install and use Windows XP Mode in Windows 7

    I wouldn't think you could damage your PC port or controller, but I'm not 100% sure (maybe 95% you will be ok) so be careful (don't blame me if something goes bang).

    - - - Updated - - -

    I have Mach3 installed and running on my development PC which is windows 7 64bit, however I have not connected to a CNC controller. So I guess some 64bit systems it may work.

    This might be a bit of a pain to do (and may not work) but you could try running an emulator so the 64 bit pretends it is a 32 bit PC:

    From Microsoft: "WOW64 is the x86 emulator that allows 32-bit Windows-based applications to run seamlessly on 64-bit Windows"
    https://msdn.microsoft.com/en-us/library/windows/desktop/aa384249%28v=vs.85%29.aspx

    Or you could try running in XP mode (I have used this to run programs that would not run on WIN7):
    http://windows.microsoft.com/en-NZ/windows7/install-and-use-windows-xp-mode-in-windows-7

    I wouldn't think you could damage your PC port or controller, but I'm not 100% sure (maybe 95% you will be ok) so be careful (don't blame me if something goes bang).



  3. #3
    Registered
    Join Date
    Jun 2008
    Location
    USA
    Posts
    562
    Downloads
    0
    Uploads
    0

    Default Re: New 64 bit computer....need help

    As long as you have the needed parallel ports, give XP mode a try with Mach3. If that doesn't work, how about downgrading the computer to a Win 7 32 bit operating system.
    You could try the forum here: Mach4 General Discussion
    I think the Dyna 1000 was made by Tom Caudle at Candcnc, you could try them: Home
    Good Luck
    Mike



  4. #4
    Member ger21's Avatar
    Join Date
    Mar 2003
    Location
    Shelby Township
    Posts
    35538
    Downloads
    1
    Uploads
    0

    Default Re: New 64 bit computer....need help

    Neither Mach3 or Mach4 can use a parallel port in a 64 bit version of windows.
    They will both work fine, however, if you use a motion controller.
    Not sure if your THC will work properly with a motion controller, though.
    You're best option is to probably by an old Pentium 4 PC with XP on it from Ebay, or Craigslist. Shouldn't be more than about $100

    Gerry

    UCCNC 2017 Screenset
    [URL]http://www.thecncwoodworker.com/2017.html[/URL]

    Mach3 2010 Screenset
    [URL]http://www.thecncwoodworker.com/2010.html[/URL]

    JointCAM - CNC Dovetails & Box Joints
    [URL]http://www.g-forcecnc.com/jointcam.html[/URL]

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  5. #5
    Member
    Join Date
    May 2007
    Location
    USA
    Posts
    111
    Downloads
    0
    Uploads
    0

    Default Re: New 64 bit computer....need help

    Still needing help on your dynacnc table?



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

New 64 bit computer....need help

New 64 bit computer....need help