Dyna Myte 2800 rebuild

Results 1 to 9 of 9

Thread: Dyna Myte 2800 rebuild

  1. #1
    Member PeteRondeau's Avatar
    Join Date
    Sep 2019
    Posts
    8
    Downloads
    0
    Uploads
    0

    Default Dyna Myte 2800 rebuild

    Ok, I've had a DM2800 for 6 years. During almost that entire time it has been disassembled for the purpose of rebuilding it. I've decided to give myself a push to get this project back on the fast track.
    To that end I'm going to upload the process to YouTube- Hopefully that will keep me focused and on track. If you'd like to follow along the first video can be found here:



    This is an overview that fast forwards the small amount of progress over the last 6 years into just a few minutes.
    Thanks!
    Pete

    Similar Threads:


  2. #2
    Member PeteRondeau's Avatar
    Join Date
    Sep 2019
    Posts
    8
    Downloads
    0
    Uploads
    0

    Default Re: Dyna Myte 2800 rebuild Part 2

    Made some more progress towards getting this machine back up and running.
    This week I fabricated the missing Z axis counter weight.



    Pete



  3. #3
    Member PeteRondeau's Avatar
    Join Date
    Sep 2019
    Posts
    8
    Downloads
    0
    Uploads
    0

    Default Dyna Myte DM2800 rebuild Part 3

    This week I began laying out the electrical panel for the DM2800 rebuild and retrofit. I have decided on the Centroid Acorn for this project. This will be my first time installing one of these. Years ago I built three Ah-Ha based machines and more recently, two Mach3 machines- so I'm hoping this will be a fun new experience. Going to try the Gecko Drive G251X modules for running the steppers.





  4. #4
    Member Fastest1's Avatar
    Join Date
    Nov 2009
    Location
    USA
    Posts
    4377
    Downloads
    0
    Uploads
    0

    Default Re: Dyna Myte 2800 rebuild

    Nice video and detail on your build.

    A lazy man does it twice.


  5. #5
    Member PeteRondeau's Avatar
    Join Date
    Sep 2019
    Posts
    8
    Downloads
    0
    Uploads
    0

    Default Re: Dyna Myte 2800 rebuild

    Thank you! Hoping to get quite a bit further on the wiring this week.



  6. #6
    Member PeteRondeau's Avatar
    Join Date
    Sep 2019
    Posts
    8
    Downloads
    0
    Uploads
    0

    Default Re: Dyna Myte 2800 rebuild

    Continuing on.
    This week I started wiring up the Centroid Acorn to the Gecko G251X stepper drives.
    Had a slight course correction in getting the step and direction signals to the drives but I think I'm on track now.





  7. #7
    Member PeteRondeau's Avatar
    Join Date
    Sep 2019
    Posts
    8
    Downloads
    0
    Uploads
    0

    Default Re: Dyna Myte 2800 rebuild

    Trying to wrap up the electrical panel by getting power to the stepper drives. Still need to hook up the spindle drive but running into a lack of documentation there. if anybody has a manual for this Electro-Craft drive marked AW0016-6423 Rev B I would certainly appreciate it!





  8. #8
    Member PeteRondeau's Avatar
    Join Date
    Sep 2019
    Posts
    8
    Downloads
    0
    Uploads
    0

    Default Re: Dyna Myte 2800 rebuild

    Working on getting the computer set up to talk to the Acorn controller, installing Centroid CNC12, and bench testing the stepper motor.





  9. #9
    Member
    Join Date
    Nov 2012
    Location
    USA
    Posts
    100
    Downloads
    0
    Uploads
    0

    Default Re: Dyna Myte 2800 rebuild

    Nice job Pete,
    Don't feel bad by 10 years. I beat you. I think I was close to 10 from the time I got fed up with my Hurco to the point where I was very close to finishing. And then, argh, the impossible happened. I found a DM4400M with a working control on it. That was a nicer machine than my Hurco, although I think my Hurco LinuxCNC control would have been nicer. But I had to build the console and the iron on the Dyna was better. Plus, the price was attractive. I got the machine for the cost of moving machinery around in the shop from which I obtained the machine. Super super nice owner who just didn't want to see the machine go to the dump, but it was obsolete by his standards and he needed the room. With all of the moving of machines around by the rigger, sharing of costs by the guy I sent the Hurco to, selling off some tooling, etc, I pretty much ended up with a tooled, working Dyna for about $300 (delivered). CAn't argue with that... But, ironically, I was then back to cleaning cleaning cleaning... 20 years of grime. And repairs... Little stuff, really, but things that needed to be done. I'm close to finishing up now. I miss my Hurco (very nice conversion) but I'm looking forward to actually cutting with a CNC mill again! I am just waiting for some caps to (hopefully) fix the heat transfer fans, and then I think I'll be ready to do some projects. Super excited and now I even have an indexer to play with.... I have to admit that I don't know G-code well though. The Hurco was all conversational, so I have to learn Fusion 360 better and the CAM to go with it. More learning...

    Anyhow, nice job on the rebuild. I always love it when people take old decrepit machinery, but which is still mechanically, and return them to service. It is a great way to keep things out of the dump, learn a whole lot, have fun, and end up with very nice machinery. So kudos to you! I look forward to reading/watching more about your machine, your experiences with Acorn, etc.

    Alan

    P.S. Oh... By the way... free is never really free! Since my acquisition, I've spent just about 1100 on parts, tooling, etc. Still a great deal, but it is kind of funny how it adds up.



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Dyna Myte 2800 rebuild

Dyna Myte 2800 rebuild

Dyna Myte 2800 rebuild