Looking for Advise / Opinions


Results 1 to 6 of 6

Thread: Looking for Advise / Opinions

  1. #1
    Member
    Join Date
    Sep 2006
    Location
    usa
    Posts
    37
    Downloads
    0
    Uploads
    0

    Default Looking for Advise / Opinions

    Wondering if I could get some opinions/advise on building a CNC router
    I want to contour, engrave, and carve 3d images in all kinds of wood.
    Size of router will be around 36" x 36"


    My question is.....which is the most ridged way to build my X and Y axis? Round linear guides, or the linear guides with the truck bearings?





    .

    Similar Threads:
    Attached Thumbnails Attached Thumbnails Looking for Advise / Opinions-linear-guides-jpg  
    Last edited by dmh13433; 09-01-2019 at 06:20 AM.


  2. #2
    Member
    Join Date
    Jan 2008
    Location
    Australia
    Posts
    1523
    Downloads
    2
    Uploads
    0

    Default Re: Looking for Advise / Opinions

    2nd option is VASTLY HUGELY BETTER than round rails.

    I have built machines with both. Would never consider using round rails again.



  3. #3
    Member ger21's Avatar
    Join Date
    Mar 2003
    Location
    Shelby Township
    Posts
    35538
    Downloads
    1
    Uploads
    0

    Default Re: Looking for Advise / Opinions

    Yes. Round rails are nut really suited for building machines. They have too much play in them.

    Gerry

    UCCNC 2017 Screenset
    [URL]http://www.thecncwoodworker.com/2017.html[/URL]

    Mach3 2010 Screenset
    [URL]http://www.thecncwoodworker.com/2010.html[/URL]

    JointCAM - CNC Dovetails & Box Joints
    [URL]http://www.g-forcecnc.com/jointcam.html[/URL]

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  4. #4
    Member
    Join Date
    Jun 2015
    Location
    Sweden
    Posts
    943
    Downloads
    0
    Uploads
    0

    Default Re: Looking for Advise / Opinions

    Square rails are much more rigid because they take up the rotational force also.
    Round rails and slides can move rotate around and they will do if your machine frame is not rigid enough.
    Also round rails have C shaped bearing which can open up from high force on them which makes them much less precise than the square slides.



  5. #5
    Member
    Join Date
    Sep 2006
    Location
    usa
    Posts
    37
    Downloads
    0
    Uploads
    0

    Default Re: Looking for Advise / Opinions

    Quote Originally Posted by ger21 View Post
    Yes. Round rails are nut really suited for building machines. They have too much play in them.

    Thanks you guys. That's what I was looking for.


    Gerry, I know you told me the AM882 is your preferred driver, and the two AM882's I bought for my other project are working amazing. I am getting 1,000 RPM out of my nema 34 motors! Most everyone I talked to said that kind of RPM could not be done with a big stepper. See the bottom of this message the string making jig I made.


    I'm wondering about this ready built controller.... https://buildbotics.com/
    I am guessing the drivers built in are probably not as good as the AM882?
    Is there other places that make a control box like this I can buy instead of building?

    I'm in the early stages of, do I build a router, or do I buy one. Sometimes I get burned out with starting a project that takes awhile, and it would be nice to start carving and learning my V Carve Pro software sooner than later.
    Any opinions on Openbuilds.com? they have a machine I've been looking at that might be a good way to start out. https://openbuildspartstore.com/lead...010-40-x-40-1/

    I know its a lot of questions, I'm just getting tired of searching and reading. Making a decision with this kind of money and time, I don't want to do something I'll regret later on.
    Thanks everyone.






  6. #6
    Member ger21's Avatar
    Join Date
    Mar 2003
    Location
    Shelby Township
    Posts
    35538
    Downloads
    1
    Uploads
    0

    Default Re: Looking for Advise / Opinions

    The first I heard of the buildbotics was a week or two ago. My first concern would be the low max voltage of 36V. Followed by the web interface, and limited flexibility. The S Curve planner is probably really smooth, though.

    I'm not sure of any other all in one unit. Maybe the TinyG or Smoothieboard type stuff.

    The Masso is a standalone control, but still needs stepper drives.

    The Leadshine MX4660 is an all in one drive, but is not a control.

    Hard to recommend any of the low cost machines, as I don't really know what you want, or expect.

    Gerry

    UCCNC 2017 Screenset
    [URL]http://www.thecncwoodworker.com/2017.html[/URL]

    Mach3 2010 Screenset
    [URL]http://www.thecncwoodworker.com/2010.html[/URL]

    JointCAM - CNC Dovetails & Box Joints
    [URL]http://www.g-forcecnc.com/jointcam.html[/URL]

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Looking for Advise / Opinions

Looking for Advise / Opinions