Hertz spindles from Turkey


Page 1 of 2 12 LastLast
Results 1 to 12 of 22

Thread: Hertz spindles from Turkey

  1. #1
    Registered
    Join Date
    Jun 2017
    Location
    Australia
    Posts
    473
    Downloads
    0
    Uploads
    0

    Default Hertz spindles from Turkey

    Hi, i am going to order a spindle motor from this supplier soon. Just wondering if anyone in Australia would like to also order a unit. The shipping for 1-5 units is 150 euro(TNT express)....it makes sense to order more than one

    Hertz spindles from Turkey-hertz-jpg
    Hertz spindles from Turkey-hertz2-jpg

    Similar Threads:
    Attached Thumbnails Attached Thumbnails Hertz spindles from Turkey-hertz-jpg   Hertz spindles from Turkey-hertz2-jpg  


  2. #2
    Gold Member
    Join Date
    May 2005
    Location
    USA
    Posts
    3590
    Downloads
    0
    Uploads
    0

    Default Re: Hertz spindles from Turkey

    Those prices are fairly cheap! I'm in the USA so I can't get into the buy party so best of luck with finding a partner.

    I must ask are you ordering directly from the manufacture or a reseller?



  3. #3
    Registered
    Join Date
    Jun 2017
    Location
    Australia
    Posts
    473
    Downloads
    0
    Uploads
    0

    Default Re: Hertz spindles from Turkey

    I was unable to find a re-seller....Initially i planned to buy a Teknomotor but the one i wanted was over $1000 Aud

    Thanks.....i might buy a couple anyway, i am sure i will build another machine after this one



  4. #4
    Registered
    Join Date
    Oct 2016
    Posts
    104
    Downloads
    0
    Uploads
    0

    Default Re: Hertz spindles from Turkey

    I have had 2 of these and Both of them broke on me. I used them to cut aluminum and they couldn’t handle it.


    Sent from my iPhone using Tapatalk



  5. #5
    Registered
    Join Date
    Jun 2017
    Location
    Australia
    Posts
    473
    Downloads
    0
    Uploads
    0

    Default Re: Hertz spindles from Turkey

    Quote Originally Posted by dillonfitz View Post
    I have had 2 of these and Both of them broke on me. I used them to cut aluminum and they couldn’t handle it.


    Sent from my iPhone using Tapatalk
    Oh no, may i ask how did they break?



  6. #6
    Registered
    Join Date
    Oct 2016
    Posts
    104
    Downloads
    0
    Uploads
    0

    Default Re: Hertz spindles from Turkey

    Quote Originally Posted by ericks View Post
    Oh no, may i ask how did they break?
    I had an er20 model and er25. The er 25 actually spun the rotor on the shaft inside the motor. It was just press-fit on so it had no power after it spun. And the er 20 version worked for about 4 months then it finally just quit working. I think the windings burnt up but I’m not 100 percent sure. I switched to a used Colombo and never had another issue.


    Sent from my iPhone using Tapatalk



  7. #7
    Registered
    Join Date
    Oct 2016
    Posts
    104
    Downloads
    0
    Uploads
    0

    Default Re: Hertz spindles from Turkey

    Quote Originally Posted by ericks View Post
    Oh no, may i ask how did they break?
    I did also use a gmt spindle with a delta drive , I never had an issue with that setup.


    Sent from my iPhone using Tapatalk



  8. #8
    Registered
    Join Date
    Jun 2017
    Location
    Australia
    Posts
    473
    Downloads
    0
    Uploads
    0

    Default Re: Hertz spindles from Turkey

    Not good....i wish you replied this a bit earlier cause i ordered a couple of motors a few minutes ago



  9. #9
    Registered
    Join Date
    Oct 2011
    Location
    Estonia
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default Re: Hertz spindles from Turkey

    Do not worry, I have been used Herz spindle three years for now. I cut aluminium and Pom plastic . Spindle is HMB42d 24000 rpm with ceramic bearings.



  10. #10
    Registered
    Join Date
    Oct 2016
    Posts
    104
    Downloads
    0
    Uploads
    0

    Default Re: Hertz spindles from Turkey

    Quote Originally Posted by ericks View Post
    Not good....i wish you replied this a bit earlier cause i ordered a couple of motors a few minutes ago
    They were great while they worked. The only thing was they were a little noisy. Sounds like a vacuum running. But for the price you can’t expect them to run forever.


    Sent from my iPhone using Tapatalk



  11. #11
    Registered
    Join Date
    Oct 2016
    Posts
    104
    Downloads
    0
    Uploads
    0

    Default Re: Hertz spindles from Turkey



    The main problem probably was that the motor can’t handle the er25 collet. The larger tooling is just too hard on the motor.


    Sent from my iPhone using Tapatalk



  12. #12
    Registered
    Join Date
    Jun 2017
    Location
    Australia
    Posts
    473
    Downloads
    0
    Uploads
    0

    Default Re: Hertz spindles from Turkey

    I see you even had the better model, the one with the steel in front....they told me to get this type for aluminium



Page 1 of 2 12 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Hertz spindles from Turkey

Hertz spindles from Turkey