Diemaking / Diecutting - Page 3


Page 3 of 7 FirstFirst 123456 ... LastLast
Threads 41 to 60 of 139

Forum: Diemaking / Diecutting

Discuss Diemaking and Diecutting here.

  1. Newbie- How much will these dies cost?

    Started by Noel.C‎, 06-01-2012 05:53 PM
    • Replies: 10
    • Views: 4,350
    05-17-2014, 12:10 PM Go to last post
  2. Die making and cutting questio

    Started by steel rule die‎, 05-17-2014 12:07 PM
    everyone, say
    • Replies: 0
    • Views: 1,616
    05-17-2014, 12:07 PM Go to last post
  3. Homemade die clicker with hydraulic press?

    Started by leathersmith‎, 02-13-2007 05:22 PM
    advised, another, clicker, cutting, hydraulic, opera, platen, press, ques, top
    • Replies: 8
    • Views: 22,152
    05-17-2014, 12:01 PM Go to last post
  4. Where to Buy Steel Rule

    Started by Hellbringer‎, 12-20-2009 02:06 AM
    • Replies: 2
    • Views: 5,358
    03-25-2014, 05:26 PM Go to last post
  5. Need a Jig for a router for a dies

    Started by the1toyplace‎, 04-06-2013 11:05 AM
    • Replies: 1
    • Views: 2,093
    03-25-2014, 04:49 PM Go to last post
  6. steel rule die through plastics?

    Started by anchange‎, 10-27-2009 01:37 PM
    • Replies: 2
    • Views: 2,903
    03-25-2014, 04:35 PM Go to last post
  7. Talking Need Help!- SFM A2 RC HARDNESS 58

    Started by JonathanH1991‎, 02-24-2014 07:02 PM
    • Replies: 0
    • Views: 1,076
    02-24-2014, 07:02 PM Go to last post
  8. Need Help!- Silver Blank making

    Started by designhawk‎, 12-19-2013 03:07 AM
    regards
    • Replies: 4
    • Views: 1,800
    12-19-2013, 10:51 PM Go to last post
  9. Need Help!- cutting aluminium foil laminated onto expanded PVC

    Started by Karl_Britton‎, 10-10-2013 11:07 AM
    kiss, onto
    • Replies: 0
    • Views: 1,521
    10-10-2013, 11:07 AM Go to last post
  10. PROBLEM: Diecut a hexagonal rod

    Started by TaigCNCer‎, 07-18-2013 03:32 PM
    diecut
    • Replies: 2
    • Views: 2,576
    07-25-2013, 12:20 PM Go to last post
  11. Problem- clearances/alignment for punching thin aluminum with unipunch frames

    Started by Jim27‎, 07-13-2013 12:23 PM
    then
    • Replies: 0
    • Views: 1,267
    07-13-2013, 12:23 PM Go to last post
  12. stamping transformer laminations

    Started by kook‎, 04-07-2010 02:33 AM
    • Replies: 11
    • Views: 3,371
    07-10-2013, 07:54 PM Go to last post
  13. Ogive help

    Started by DAVE A‎, 06-23-2013 07:48 AM
    • Replies: 4
    • Views: 1,497
    06-25-2013, 04:35 PM Go to last post
  14. Need Help!- Building a paper punch, need help designing the punches.

    Started by basalt‎, 09-22-2011 08:09 PM
    welcome
    • Replies: 2
    • Views: 2,758
    03-15-2013, 06:35 PM Go to last post
  15. Embossing die advice for 0.027 inch aluminum

    Started by Jim27‎, 02-23-2013 01:55 PM
    goes
    • Replies: 1
    • Views: 1,565
    03-15-2013, 06:20 PM Go to last post
  16. How much do you guys pay for Dies ?

    Started by LuciCharm‎, 08-15-2009 12:21 AM
    • Replies: 6
    • Views: 5,316
    12-16-2012, 10:50 PM Go to last post
  17. Dinosaur Trade

    Started by roninB4‎, 11-17-2009 09:55 AM
    2 Pages
    1 2
    abroad, asking, away, not, retire, since, then, tool and die
    • Replies: 34
    • Views: 13,652
    11-18-2012, 09:01 AM Go to last post
  18. Question Die Grinder Help

    Started by Dave's_Not_Here‎, 03-20-2007 03:52 AM
    equally, went
    • Replies: 5
    • Views: 7,094
    08-09-2012, 04:04 PM Go to last post
  19. Need Help!- Engraving Cutter Help

    Started by Jafwiz‎, 07-27-2012 12:15 PM
    • Replies: 2
    • Views: 1,570
    07-28-2012, 12:31 PM Go to last post
  20. Steel Rule Automatic Bender

    Started by ddanutz1‎, 06-21-2008 03:18 PM
    • Replies: 8
    • Views: 8,510
    03-18-2012, 03:10 PM Go to last post

Page 3 of 7 FirstFirst 123456 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 5 users browsing this forum. (0 members & 5 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands