DeskCNC Controller Board


Page 1 of 8 1234 ... LastLast
Threads 1 to 20 of 151

Forum: DeskCNC Controller Board

Discuss DeskCNC Controller Boards and the software that controls it here.

  1. Unhappy G or M code for tool change

    Started by bradyfb‎, 12-10-2007 06:28 PM
    its, next, then
    • Replies: 14
    • Views: 21,437
    12-19-2007, 09:27 PM Go to last post
  2. DeskCNC Software Probs

    Started by Rob 1264‎, 03-13-2007 08:33 AM
    .90
    • Replies: 14
    • Views: 10,162
    05-04-2010, 05:07 PM Go to last post
  3. DesclCNC Board and Mach2

    Started by dewayne‎, 10-09-2004 09:08 AM
    board, cadcut, controller, look, mach2, marriage, software, suggestions
    • Replies: 15
    • Views: 9,989
    03-03-2009, 12:35 PM Go to last post
  4. Smile DeskCNC about a lot of stuff!

    Started by kolokithas‎, 03-02-2007 05:44 PM
    dxf design, its, maybe, ques
    • Replies: 16
    • Views: 8,382
    11-02-2007, 10:57 PM Go to last post
  5. Proximity switches with optocoupler adapter

    Started by Jamesdee‎, 01-18-2015 01:53 PM
    • Replies: 15
    • Views: 7,682
    02-16-2019, 04:15 PM Go to last post
  6. Need Help!- Db25 1205 bob

    Started by brontoo26‎, 12-26-2015 02:29 AM
    • Replies: 6
    • Views: 7,602
    09-08-2018, 03:03 AM Go to last post
  7. Question plans for joystick controller

    Started by erkiwi‎, 06-08-2007 03:48 AM
    • Replies: 6
    • Views: 7,561
    11-14-2008, 11:07 AM Go to last post
  8. Question Filling the machine velocity tab

    Started by kolokithas‎, 01-20-2007 08:05 PM
    46600, maximum, motors, rps, velocity
    • Replies: 13
    • Views: 6,605
    09-25-2010, 05:21 PM Go to last post
  9. How do you hook up limit and home switches?

    Started by cncadmin‎, 11-07-2004 07:45 PM
    axis, goes, home, limit, machine, maybe, next, switch
    • Replies: 6
    • Views: 6,486
    09-23-2007, 04:34 PM Go to last post
  10. Question Newbie- Stepper Driver 4.2A DQ542MA or PM542

    Started by kunte‎, 06-16-2011 06:35 AM
    motor-controller, not, since
    • Replies: 0
    • Views: 6,367
    06-16-2011, 06:35 AM Go to last post
  11. DeskCNC - Should I Deep Six it?

    Started by Cmguitar‎, 06-26-2017 11:37 PM
    • Replies: 9
    • Views: 5,857
    03-13-2019, 03:52 PM Go to last post
  12. Need Help!- Mach3

    Started by Snakips‎, 06-16-2017 06:59 AM
    2 Pages
    1 2
    • Replies: 24
    • Views: 5,721
    06-23-2017, 12:55 AM Go to last post
  13. Exclamation Need Help!- Mechatronics 4axis stepper board

    Started by ironaxe2008‎, 08-29-2008 04:27 AM
    • Replies: 1
    • Views: 5,674
    01-01-2009, 11:47 AM Go to last post
  14. Unhappy random estop

    Started by erase42‎, 11-06-2006 10:33 AM
    2 Pages
    1 2
    1.7, board, compu, estop, its, lates, made, ques, random, since, times
    • Replies: 21
    • Views: 5,535
    02-02-2007, 06:28 PM Go to last post
  15. DeskCNC 2nd. gen controller AND HobbyCNC Pro Controller

    Started by maycom‎, 06-02-2007 03:12 AM
    • Replies: 1
    • Views: 5,392
    06-02-2007, 02:33 PM Go to last post
  16. Need Help!- Auto Z probe work in mach3 setup problems

    Started by scheelman‎, 12-10-2018 03:59 AM
    auto, mach3, probe, setup, work
    • Replies: 3
    • Views: 4,575
    12-11-2018, 11:24 AM Go to last post
  17. Deskcnc lathe threading

    Started by jed102‎, 09-14-2006 12:30 PM
    • Replies: 11
    • Views: 4,470
    01-16-2008, 08:50 AM Go to last post
  18. Need Help!- DeskCNC Cutting Arc Problems

    Started by HobbyCAD‎, 06-07-2010 04:57 AM
    not
    • Replies: 10
    • Views: 4,461
    06-23-2010, 10:32 AM Go to last post
  19. Angry Tool height "touch off" tool unusable

    Started by DHK‎, 07-14-2004 07:14 PM
    axis, deskcnc, direction, down, fixed, hardware, home, macro, manufacturer, motion, offset, probe, programming, scan, scanning, servo, slow, software, switch, system, tool, tool library, tool offset, touch, wiring, z axis
    • Replies: 6
    • Views: 4,420
    05-06-2006, 01:54 PM Go to last post

Page 1 of 8 1234 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 3 users browsing this forum. (0 members & 3 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands